00191025-01.pdf - 第605页

19 Error Messages S IPLACE 80S/F/G User’s Manual 19.1 Error Mess ages Edition 12/96 from Software Vers ion SR.009.xx 19 - 18 201 Track e mpty, opti cal centeri ng incorrect CAUSE ● 3 optica l measuri ng errors wi th comp…

100%1 / 736
SIPLACE 80S/F/G User’s Manual 19 Error Messages
Edition 12/96 from Software Version SR.009.xx 19.1 Error Messages
19 - 17
158 Limit switch of width adjustment for minimum width actuated
CAUSE
●
Conveyor belt width has been set too small
REMEDY
●
Increase conveyor belt width
159 Limit switch of width adjustment for maximum width actuated
CAUSE
●
Conveyor belt width has been set too large
REMEDY
●
Reduce conveyor belt width
160 Bero not found during conveyor belt width check
CAUSE
●
Conveyor belt bero is defective or set incorrectly
REMEDY
●
Check bero
161 Bero covered before conveyor belt width check
CAUSE
●
Conveyor belt bero responds before the actual position (gantry) is reached
REMEDY
●
Adjust bero
162 WPC must be moved from refill position
CAUSE
●
WPC is in the refill position
REMEDY
●
The operator should quit the refill position in the "Refill" "Location1" menu.
163 Conveyor belt width out of travel range
CAUSE
●
The conveyor width detected lies outside of the possible range of values.
The sensing distance of the bero has been set too high.
The bero is defective.
REMEDY
●
Use the SITEST program to re-register the 100mm board and run width measurement again.
The sensing distance of the bero has been set too high.
Replace bero.
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 18
201 Track empty, optical centering incorrect
CAUSE
●
3 optical measuring errors with component from one track; set up for incorrect component.
Incorrect angle has been input for the component in the feeder.
REMEDY
●
Check components feed; fill up empty track and reset track.
check set-up data.
202 Track empty, measure value outside tol.
CAUSE
●
3 electrical measurement errors with component from one track
REMEDY
●
Check components feed; fill up empty track and reset track.
203 Track set empty by operator
CAUSE
●
Under the menu "Refill" track set to empty.
REMEDY
●
Reset track in the menu "Refill".
204 Z axis cannot be moved upwards
CAUSE
●
When the start button pressed Z axis not in top position.
REMEDY
●
Check servo, push Z axis upwards by hand.
205 BERO for Z axis top position not released
CAUSE
●
Sensing distance too great; Bero defective; cam disk not tightened up correctly; z zero point correc-
tion value incorrect; counting error.
REMEDY
●
Adjust sensing distance; replace Bero; tighten up cam disk; redetermine z zero point correction; fit
new motor/tacho/encoder; carry out axis calibration.
206 Fault in pick-up station during vac. meas.
CAUSE
●
Suction face of the nozzle damaged; nozzle too small; component was not supplied.
REMEDY
●
Fit new nozzle; check component feed.
SIPLACE 80S/F/G User’s Manual 19 Error Messages
Edition 12/96 from Software Version SR.009.xx 19.1 Error Messages
19 - 19
207 Fault in placement stat. during vac. meas.
CAUSE
●
Suction face of the nozzle damaged; nozzle too small; jaws of the centering station bouncing; com-
ponent was not picked up properly; vacuum in the holding circuit too low; vacuum board defective.
REMEDY
●
Fit new nozzle; calibration of the motor control board; check component feed, call SMD Service.
208 End position BERO of centering station not being actuated
CAUSE
●
End position Bero defective or incorrectly set; recuperator spring of the centering station worn out.
REMEDY
●
Fit new Bero, adjust; maintain centering station.
209 Counting error X axis
CAUSE
●
Scales dirty (incremental encoder).
REMEDY
●
Clean scales (incremental encoder).
210 Measurement trigger BERO of centering station not actuated
CAUSE
●
Distance between Bero and actuator flag too great; Bero defective
REMEDY
●
Correct distance to actuator flag; fit new Bero.
211 Counting error Y axis
CAUSE
●
Scales dirty (incremental encoder).
REMEDY
●
Clean scales (incremental encoder).
212 Fault during vacuum measuring in reject position
CAUSE
●
O-ring on the sealing piston damaged.
REMEDY
●
Fit new O-ring to the sealing piston.
213 Timeout during reception from coplanarity
CAUSE
●
Coplanarity module not plugged in
REMEDY
●
Plug in module