00191025-01.pdf - 第446页
SIPLACE 80S/F/G User’s Manual 9 Maintenance Edition 07/97 from S oftware Version SR.010.xx 9.6 IC Head (SIPLACE 80F) 9 - 87 Fig. 9.6.11 Specifying the gara ge numbers in the nozzle changer Key to Fig. 9.6.11 1 Nozzle cha…
9 Maintenance SIPLACE 80S/F/G User’s Manual
9.6 IC Head (SIPLACE 80F) Edition 07/97 from Software Version SR.010.xx
9 - 86
5 Diaphragm: item no. 309 458
6 Nozzle: item no. 309 456
7 Diaphragm: item no. 307 052
8 Nozzle: item no. 307 051
Sequence of work in
Fig. 9.6.10
A Pull off the sleeve.
B Remove the diaphragm.
C Clean the sleeve with alcohol and dry it before refitting.
D Rub the annular surface of the new diaphragm sparingly with talcum, keeping it absolutely free of grease.
∆
!
Slide the sleeve back in as far as it will go.
9.6.6.4 Inserting Nozzles into the Nozzle Changer
●
After maintenance insert the nozzles by hand into their correct assigned places (by referring to the notes
you took when you removed them ) in the nozzle changer.
●
Insert the nozzle removal tool into each nozzle in turn and turn the nozzle anticlockwise until it locks in the
nozzle changer. Lift the tool vertically upwards and out.
●
Close the safety hoods and swivel doors and switch the machine on.
●
Have the allocations of nozzles to garage numbers displayed by making the following selection :
Single functions
→
Gantry 1
→
Nozzle configuration IC head
NOTE
You can only use this function when you have returned the current nozzle not by hand but, as described,
by using the
Return nozzle
function.
●
A table will be shown on the screen with the garage numbers (pick-up location numbers) and the actual
and programmed occupancies. Insert the nozzles into the nozzle changer in accordance with the ACTUAL
assignments.
●
Check to make sure the nozzles are properly latched.
NOTE
If the nozzles are not properly latched this will lead to errors in picking up the nozzle, while incorrectly
assigned nozzles will result in component pick-up errors.
●
At the start of placement the current nozzle as specified in the placement program will be picked up.
SIPLACE 80S/F/G User’s Manual 9 Maintenance
Edition 07/97 from Software Version SR.010.xx 9.6 IC Head (SIPLACE 80F)
9 - 87
Fig. 9.6.11 Specifying the garage numbers in the nozzle changer
Key to Fig. 9.6.11
1 Nozzle changer
2 Turn the nozzle counter-clockwise until it locks in place.
3 PCB transport direction
9.6.7 IC-Head Nozzle Survey
Designation Type Item number
Nozzle, 12.5 in dia. 418 00322544-01
Diaphragm for nozzle, 12.5 in dia. 00307052-03
Nozzle, 24 in dia. 419 00322546-01
Diaphragm for nozzle, 24 in dia. 00310569-03
Nozzle, 8 in dia. 417 00322543-01
Nozzle 3 x 6 416 00322545-01
Tab. 9.6.1 IC-head nozzle survey
9 Maintenance SIPLACE 80S/F/G User’s Manual
9.6 IC Head (SIPLACE 80F) Edition 07/97 from Software Version SR.010.xx
9 - 88