SG_FSE_SiplaceHF_HF3_00193901-05_eng.pdf - 第369页

1 - 1 S tudent Guide SIPLACE HF/HF3 Edition 09/2005 8 Co mponent handling 1 8 Component handling 8.1 Overview These chapte r includes the topics o f component ch ang eover table (COT) the relevan t docking unit and the p…

1 - 2

Student Guide SIPLACE HF/HF3

Contents Edition 09/2005

1 - 1

Student Guide SIPLACE HF/HF3

Edition 09/2005 8 Component handling

8 Component handling

8.1 Overview

These chapter includes the topics of component changeover table (COT) the relevant docking unit

and the pneumatic tape cutter.

Four moveable component changeover tables could be docking on the HF/HF3-machine. On lo-

cation 2 and/or 4 on the HF the MTC 2 can be set up or retrofitted as an option. On the HF3 ma-

chine can be set the MTC 2 only on location 2. The component changeover tables can be "dock"

or "undock" by activation of one or two of the buttons, depend on the construction.

Fig. 8.1 - 1 Shows the buttons for docking and undocking the COT‘s

1. Button for undocking the component changeover tables (for model with two hand operation)

2. Button together with button (1) for docking the component changeover tables

3. Button for docking and undocking the COT for machine version ’A’ which have one hand oper-

ation.

1 - 2

Student Guide SIPLACE HF/HF3

8 Component handling Edition 09/2005

Technical Data component table: 8

8.1.1 Component changeover table (COT)

The component handling unit consist of the COT and the docking unit with tape cutter.

COT model 1 with Two -Hand -Operation 8

For the docking process, push the component changeover table into the docking unit as much as

possible. Mount COT by activating the two buttons (see Fig. 10.1 - 1) to the machine. Than the

feeder is lifted and pulled towards the machine by two pneumatic cylinders and cam disks.

For the undocking process, open the cover and press the button 1 (see Fig. 10.1 - 1). Than the

feeder table is pushed out and lowered. This happen by two pneumatic cylinders and the two

pneumatic cylinders operating the cam disks.

Electrical and pneumatical supply is automatically connected by a central ODU-connector in the

docking unit.

Fig. 8.1 - 2 COT -model 1 with the docking unit

Feeder capacity

180 tracks width 8mm (3x8mm S feeder)

120 tracks width 8mm (2x8mm S feeder)

Location

4 Component tables with the integrated tape waste container

15 tracks via 30mm for each component table or up to 2 matrix tray changer

undocking

with electric and pneumatic supply or completely manuell when machine is OFF

docking

only with electric and pneumatic supply

Feeder types

Tapes, Bulkcase, Linear magazin, Siplace S-Feeder(F4,F5,S-20,S-

23,S25HM,S27HM,HS50,HS50+,HS60), OEM Feeder, Surftape feeder (8, 12,

16, 24 mm), manual Trays

Interface to the machine

automatically connection if docking the COT

- connect to Power - connect to CAN Bus

- connect to Safety loop - connect to pneumatic air

- connect to the option Splice detection

Component table height

depend from the machine height: Freely adjustable on following SMEMA heights

830 mm ± 15 mm (Standard) 900 mm ± 15 mm (SMEMA)

930 mm ± 15 mm (SMEMA) 950 mm ± 15 mm (SMEMA)