00194614-08 Trainingsdoku. SG X-Serie_X4i SW70x (AL2)_EN.pdf - 第313页
Collect, Pick and Place Head (CPP) Nozzle Changer Calibrating the Segment Offset 313 Student Guide SIPLACE X-Serie and X4I SW70x (AL2) ► Select Service (Configure, update and calibrate the machine) . ► Select Single cali…
Collect, Pick and Place Head (CPP)
Calibrating the Segment Offset Settings on the CPP Head
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 312
Conversion
Calibrating the Segment Offset
8.5.3 Calibrating the Segment Offset
► Switch over to the operator level Machine Service.
(1) Holding bracket (2) "Head bottom" position
(3) "Head top" position (4) Fixture holes with bushings
Legend
1. Drilling for the fastening screw of the bushing in "head
bottom" position
2. Drilling for the fastening screw of the bushing in "head
top" position
3. Bushing"
All four bushings must either be fixed in top or bottom
position.
Proceed as follows when replacing the bushings:
► Undo the fastening screws of the bushings.
► Insert the bushings in the correct position and re-
tighten them.
► Perform these steps for all four bushings and the
holding bracket of the head.
Collect, Pick and Place Head (CPP)
Nozzle Changer Calibrating the Segment Offset
313 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
► Select Service (Configure, update and calibrate the machine) .
► Select Single calibration.
► Select Head calibration.
► Select Calibrate segments...
► Select the segments to be calibrated and then click on Start calibration.
Nozzle Changer
8.6 Nozzle Changer
1. Nozzle changer frame
2. Push button for NC magazine release.
3. Actuator to open and close the NC magazines via software.
4. Monitor NC magazines, switches 1, 2 & 3.
5. Spring pins to mount the NC magazines.
Nozzle changer SX and X Machine
On the NC frame of the SX-machine you can mount 4 magazines with twelve 20xx nozzles or eight 28xx
nozzles. All together a maximum of four nozzle changers can be install on one location, so that you can
have 16 magazines.
On the X-series machine a maximum of two nozzle changer rows with 6 magazines per row can be
mounted on one location. With the X4i only one row per location is possible.
The mechanical construction and function of both nozzle changer are the same, but with additional
functionality:
▪ Recognition the type of magazine
▪ Height monitoring of the magazines
▪ The status of the switches will be checked after switching ON the machine and when the machine
cover is closed.
Collect, Pick and Place Head (CPP)
Structure of 20xx Nozzle Magazines Nozzle Magazines
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 314
– 10xx magazine (C&P20A): Switch 2 (middle) activated
– 20xx magazine (CPP): Switch 1 and 3 activated
– 28xx magazine (CPP): Switch 1, 2 and 3 activated
Nozzle Magazines
8.7 Nozzle Magazines
Structure of 20xx Nozzle Magazines
8.7.1 Structure of 20xx Nozzle Magazines
Structure of 28xx Nozzle Magazines
8.7.2 Structure of 28xx Nozzle Magazines
Nozzle Statio ns
8.8 Nozzle Stations
Universal Nozzle Station for SX and X Series (X2, X3, X4 )
8.8.1 Universal Nozzle Station for SX and X Series (X2, X3, X4)
Nozzle station
The C&P20A nozzle station has been extended to include nozzle types for the CPP head:
▪ Reject station for C&P20A and CPP nozzles
▪ Take off for 20xx nozzles
▪ 12 garages per magazine
▪ Antirotation guard for nozzles
▪ Special nozzles up to a max. length of 16.5 mm
▪ Two fiducials per magazine
Legend
1. Five garages for nozzles with a length of up to
12.5 mm (garages 1, 5, 6, 8, 9)
2. Four garages for special nozzles with a length of up
to 16.5 mm (garages 2, 3, 4, 7)
3. Level surface – this is used by special nozzles for
orientation purposes, when they are nonsymmetrical.
The standard 28xx nozzles are symmetrical.
▪ Antirotation guard for nozzles
▪ Two fiducials per magazine
Legend
1. Take off for 28xx nozzles
2. Reject station for C&P20A and CPP nozzles
3. Take off for 20xx nozzles
4. Take off for 10xx nozzles