00194614-08 Trainingsdoku. SG X-Serie_X4i SW70x (AL2)_EN.pdf - 第60页
Overview X/Y Axis Construction Overview of Components Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 60 X/Y Ax is Con struct ion 3.2.7 X/Y Axis Construction X Axis Co nstruction 3.2.7.1 X Axis Construction X Axis Cons…
Overview
Overview of Components Changeover Table Components
59 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
The changeover table can be manually set to the following PCB conveyor heights
▪ 830 mm ±15 mm standard height
▪ 900 mm ±15 mm SMEMA height
▪ 930 mm ±15 mm SMEMA height
▪ 950 mm ±15 mm SMEMA height
Overview of X Feeders
3.2.6.3 Overview of X Feeders
X Feeder Operator Panel
Example 8 mm X feeder
Legend
1. Pickup position
2. Motors for moving components
3. Motor for cover foil
4. Display, operating panel and status display
5. Mechanical and electrical unlocking function
The new generation of X feeders enables you to set up a
separate feeder for each component used at the
machines (single track feeders). This ensures optimum
use of the machine locations and optimum configuration
of the setups in the placement process.
The X feeders can be logged off should errors occur
during production and can then be replaced by other
feeders, which are logged back into the production run.
As an option, a splice sensor can be directly integrated
into the feeder.
X Feeder Operator Panel
Legend
1. "Forwards" button
Press briefly to move the tape by the set cycle step.
Press for longer to move the tape forwards. Make
sure the cover foil is not clamped in.
2. "Backwards" button
Press briefly and release slowly to move the tape
backwards by the set cycle step
Prolonged pressing moves the tape back. (Both
functions should only be performed without the cover
foil fitted).
3. Press the "Foil" button to start the foil drive motor.
This runs until the foil has been stretched tight and
the motor toggle switch turns off or until the timer has
counted 30 seconds.
4. Briefly press the "SET" button to switch over to the
next menu on the main menu level. Press for longer
to request component verification.
5. Display showing track on location
6. Cycle step
7. Transport direction
Overview
X/Y Axis Construction Overview of Components
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 60
X/Y Axis Construction
3.2.7 X/Y Axis Construction
X Axis Co nstruction
3.2.7.1 X Axis Construction
X Axis Construction
Legend – main X axis modules
The following modules are installed on the head mount (2):
▪ PCB camera (6)
▪ Head board with Vision board (7) (head interface, head adapter)
▪ Incremental encoder
▪ C&P20A head, CPP head or Twin Head
The gantry arm (1) is made of carbon fiber. This gives the gantry arm high torsional rigidity with minimum
weight. The X axis is driven by a linear motor. The secondary part of the drive consists of a permanent
magnet and is fixed to the gantry arm, while the primary part is screwed to the head mounting plate.
1 Gantry X (frame) 5 Linear drive permanent magnet
(secondary)
2 Fixture plate with head X linear motor
(primary)
6 PCB camera mount
3 Linear incremental encoder 7 Head interface board
4 Linear guide rails X axis 8 X trailing cable
Overview
Overview of Components SIPLACE Vision
61 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
X Axis Te chnical Data
3.2.7.2 X Axis Technical Data
Y Axis Co nstruction
3.2.7.3 Y Axis Construction
Y Axis Te chnical Data
3.2.7.4 Y Axis Technical Data
SIPLACE Vision
3.2.8 SIPLACE Vision
The new digital SIPLACE Vision solution is another step towards the satisfaction of customer demands
for greater speed, flexibility and robustness.
Advantages of the digital Vision system:
▪ Robust and fast computing algorithms
▪ Flexible measurement processes
▪ Self-learning graphical interface
▪ Geometric description of components at the machine
▪ State-of-the-art digital camera hardware
Drive Direct, linear drive
Maximum speed 2.5 m/sec.
Travel range 471 mm
Mechanical travel range 480 mm
Measuring system Linear incremental encoder
Length of linear incremental encoder 520 mm
Resolution 1 µm
Y Axis Construction
Legend – main Y axis modules
1. Linear drive permanent magnet (secondary)
2. Linear guide rails
3. Linear incremental encoder
4. Trailing cable
5. Linear motor (primary)
The Y axis is driven by a linear motor. The secondary part
of the drive consists of a permanent magnet and is fixed
to the machine frame. The primary part is screwed to the
gantry arm.
Drive Direct, linear drive
Maximum speed 2.5 m/sec.
Gantry travel range 1430 mm
Length of incremental encoder 1850 mm
Resolution 1 µm