4OM-1603-007_w.pdf - 第124页

4OM-1603 1-69 6. Head Change Procedure (Hard) : Chap.1 1202-002 6.1 Re-T eaching Items in Head Change Work Priority T eaching Item T eaching T ype High Speed Head Multi-Fu nction Head 1 NL-Axis Origin / Master Nozzle Lev…

100%1 / 379
4OM-1603
1-68
6. Head Change Procedure (Hard) : Chap.1
1202-002
(10) Push the head against the unit lower section.
(11) Fasten the head set bolts M6.
(12) Fasten the round head screws on the rear of the control box.
(13) Connect the connector.
(14) Connect the piping tubes.
(15) Connect the ber optic cables to the multi-axis board.
(16) Set up the rotary switch.
High Speed Head (Rear Side) : 0
High Speed Head (Front Side) : 1
Multi-Function Head (Rear Side) Upper Board : 0
Multi-Function Head (Rear Side) Lower Board : 2
Multi-Function Head (Front Side) Upper Board : 1
Multi-Function Head (Front Side) Lower Board : 3
Rotary Switch
Multi-Function Head (Upper Board)
Rotary Switch
Multi-Function Head (Lower Board)
Rotary Switch
F4A49
(17) Turn the air switch to the supply side and turn on the power to the machine.
4OM-1603
1-69
6. Head Change Procedure (Hard) : Chap.1
1202-002
6.1 Re-Teaching Items in Head Change
Work
Priority
Teaching Item
Teaching
Type
High Speed
Head
Multi-Function
Head
1
NL-Axis Origin / Master Nozzle Level Automatic
○
2
Chute Level (At the time of shipping) Automatic
(At the time of head change) Automatic
○ ○
3
PEC Recognition Camera & Beam Automatic
○ ○
4
Component Recognition Camera Position Automatic
○ ○
5
Head Rotational Angle Axis Automatic
○ ○
6
Head Rotational Center / Reference Mark Position Automatic
○ ○
7
Fly Recognition Camera Automatic
○
8
Nozzle Inclination Automatic
○
9
Precision
Adjustment
①
Head Offset (A) Manual
○
②
Head Offset (ΔA), (B) Manual
○
③
Head Offset (B) For Each Angle Manual
○
T4A16
Note
(a) For the teaching items, perform each of them in the order of precedence.
(b) When any of the heads is changed from the high-speed head to the multi-
functional head, perform the steps "6", "7" and "8" also for unchanged
high-speed heads.
4OM-1603
1-70
6. Head Change Procedure (Hard) : Chap.1
1202-002
6.2 Required Material List for Teaching and Precision
Adjustment (At the time of Head Change)
Product Item Part No. Q'ty Traching
Precision
Adjustment
Common
1 BARON 1
○
2 BARON Glass PCB 1
○
3 Adhesive Double Coated Tape 1
○
4 Offset Calculation Sheet 1
○
High-Speed Head Adjustment (For Single Head Mode)
1 0603 Master Chip Component 0914J10A 1
○
2 QFP Glass Jig 211D9639 1
○
3 GD28081 Feeder 1
○
4 HA09 Nozzle 1
○
5 HG31 Nozzle 15
○
6 Master Nozzle 1
○
Multi-Function Head Adjustment (In the Use of Feeder Cart)
1 QFP Glass Jig 8
○ ○
2 Jig Placement Plate 1
○
3 Jig Bracket (1) 1
○
4 Jig Bracket (2) 1
○
5 M3×10 Sems Screw 4
○
6 FA04 Nozzle 1(3)
○
7 FF01 Nozzle 1(3)
○ ○
T4A18