4OM-1603-007_w.pdf - 第287页

4OM-1603 3-1 12 3. Error IDs and Remedial Procedures : Chap.3 1 109-006 Error ID Error Name, Description, Cause, and Remedy 4b2301 Feeder (Servo Error) Alarm Code:A0 - Internal Parameter Error (Breakdown of Control P .C.…

100%1 / 379
4OM-1603
3-111
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
4b2009 P.C.B Height Measurement
Detected a curve more than permission values. (- direction)
-----
4b200a P.C.B Height Measurement
Error of the result measured by a master jig (height)
Check if the master jig (height) has some dirt and foreign particles.
4b200b P.C.B Height Measurement
Failed in wearing height revision.
-----
4b200c P.C.B Height Measurement
An abnormal measurement was detected by the multipoint measurement.
Check the measurement position.
4b200d P.C.B Height Measurement
Recovery by the multipoint measurement failed because the measurement result
wasinsufcient.
Check the measurement position.
4b2011 P.C.B Height Measurement
Measurement time-out
-----
4b2081 P.C.B Height Measurement
Abnormality occurred for communication with a sensor
-----
4b2082 P.C.B Height Measurement
Failed in wearing height revision.
-----
4b2083 P.C.B Height Measurement
Measurement time-out
-----
4b2084 P.C.B Height Measurement
The coordinate where the height measurement was impossible was appointed.
Please appoint a coordinate in a measurable range.
4b2101 SSC network abnormal
There is abnormal in SSC network.
PleaseconrmthecableofSSCnetwork.
4b2102 SSC network abnormal
ThereisaprobleminconnectiontoServoAmplier(XY).
(1) Shut down the machine and check the connection between the position board
andamplier.
(2)Checkwhetherornottheservoampliersaredamaged.
4b2103 SSC network abnormal
ThereisaprobleminconnectiontoServoAmplier(Head).
(1) Shut down the machine and check the connection between the position board
andamplier.
(2)Checkwhetherornottheservoampliersaredamaged.
4OM-1603
3-112
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
4b2301 Feeder (Servo Error)
Alarm Code:A0 - Internal Parameter Error (Breakdown of Control P.C.B.)
Please replace the feeder. (Do not disconnect the feeder in powering on,
otherwise it may cause the inside data broken.)
4b2302 Feeder (Servo Error)
Alarm Code:A1 - Over Current Error (Foreign substances in the tape feeding drive
section)
Conrmwhetherornotthetapeisbeingjammedonthepath./Conrmthereelto
operatesmoothly./Conrmwhetherornotsomecomponentsanddustarebeing
caughtinthesprocket./Conrmwhetherornotsomecomponentsanddustare
being caught in the tape feeding gear.
4b2303 Feeder (Servo Error)
Alarm Code:A2 - Others
-----
4b2304 Feeder (Servo Error)
Alarm Code:A3 - Others
-----
4b2305 Feeder (Servo Error)
Alarm Code:A4 - Main Circuit Power Supply Error (Please check the power supply
voltage.) (G04)
Please check the power supply voltage.
4b2306 Feeder (Servo Error)
Alarm Code:A5 - Fault Speed Error (Tape catching)
Conrmwhetherornotthetapeisbeingjammedonthepath.
Conrmthereeltooperatesmoothly.
Conrmwhetherornotsomecomponentsanddustarebeingcaughtinthe
sprocket.
Conrmwhetherornotsomecomponentsanddustarebeingcaughtinthetape
feeding gear.
4b2307 Feeder (Servo Error)
Alarm Code:A6 - Others
-----
4b2308 Feeder (Servo Error)
Alarm Code:A7 - Fault Load Error (Tape twisting, Catching foreign substances)
Conrmwhetherornotthetapeisbeingjammedonthepath.
Conrmthereeltooperatesmoothly.
Conrmwhetherornotsomecomponentsanddustarebeingcaughtinthe
sprocket.
Conrmwhetherornotsomecomponentsanddustarebeingcaughtinthetape
feeding gear.
4b2309 Feeder (Servo Error)
Alarm Code:A8 - Encoder Error (Breaking wire, Breakdown of control P.C.B. and
Defective servo motor)
Please replace the feeder.
4b230a Feeder (Servo Error)
Alarm Code:Ab - System Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4OM-1603
3-113
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
4b230b Feeder (Servo Error)
Alarm Code:Ac - Reckless Run Detection Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4b230c Feeder (Servo Error)
Alarm Code:Ad - Excessive deviation in position
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
4b2401 Feeder (Movement Error)
Alarm Code:E0 - (1) Damaged cover tape/ (2) Cover tape jammed in the storage/
(3) Splicing section peeling off
(1)Conrmwhetherornotthecovertapeissetcorrectly
(2) Please remove the cover tape from the storage section.
(3) Please check the splicing condition if the work performed correctly in the
process.
4b2402 Feeder (Movement Error)
Alarm Code:E1 - Cover tape peeling off error (Get caught up)
(1)Conrmwhetherornotthecovertapeissetcorrectly.
(2)Conrmwhetherornotsomestickymaterialhasadheredtothesuppressor.
(3)Conrmthesplicingconditioniftheworkperformedcorrectlyintheprocess.
4b2403 Feeder (Movement Error)
Alarm Code:E2 - Origin Position Checking Error (Excessively out of the origin
during servo ON)
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
4b2405 Feeder (Movement Error)
Alarm Code:E4 - Positioning Completion Timeout (Foreign substances in the
sprocket wheel)
Conrmwhetherornotthetapeisbeingjammedonthepath.
Conrmthereeltooperatesmoothly.
Conrmwhetherornotsomecomponentsanddustarebeingcaughtinthe
sprocket.
4b2407 Feeder (Movement Error)
Alarm Code:E6 - Lane Change Timeout Error
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
4b2408 Feeder (Movement Error)
Alarm Code:E7 - Servo ON Timeout
If the error occurs frequently, replace the feeder.
(It may be caused by trouble of the control P.C.B..)
4b2410 Feeder (Movement Error)
A pickup error occurred due to feeder operation problem.
Please check the feeder and the component.
-----