4OM-1603-007_w.pdf - 第25页

Safety Precautions Safe-14 1OM-1603 Alert Indications described as " CAUTION " (continued) Alert Description Related Items The padlock key should be kept in such a way that nobody except the personnel in charge…

100%1 / 379
Safety Precautions
Safe-13
1OM-1603
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
Watchyourstep!
·
Be careful not to hit your foot against the cart while moving the bank
feeder change cart.
Especially, the resistance against cart movement may change rapidly
when the oor is ragged and the cart gets caught on the oor or
a sheet is used and the cart gets caught at the edge or a slackened
portion of the sheet.
·
Make sure to insert the feeder into the deep end.
When the tape feeder is mounted onto the feeder carriage, make sure
that it has been inserted into the deep end and xed securely.
In the case that it has not been xed securely, the tape feeder might
fall, which might cause a lower leg injury or damage to the feeder.
"3.8.1" in
"Chapter 1 (Vol. 1)"
"2.2.4" in
"Chapter 3 (Vol. 1)"
Do not put your hand in the moving area while the feeder base is
moving up or down.
While the LED of the Feeder Ready switches are being ickering, it
indicates that the corresponding feeder base is moving up and down.
"2.2.5" in
"Chapter 1 (Vol. 1)"
When you need to bend down to perform work, you may hit your
head on the tape feeder worktable and get injured.
"2.2.6.1" in
"Chapter 3 (Vol. 1)"
When the tape feeder connecting cable is connected to the tape
feeder, unless the tape feeder is held securely, the tape feeder
holding guide may come off and drop from the tape feeder unit.
Connect the cable with the tape feeder held securely.
"2.2.6.1" in
"Chapter 3 (Vol. 1)"
There are some heavy feeder models. When such feeders are
removed with one hand, the weight of the feeder removed from
the guide cannot be supported by one hand and the feeder might
drop. Remove the feeder using both hands to support it.
"2.2.6.2" in
"Chapter 3 (Vol. 1)"
1108-006
4. Alert Indications in Instruction Manual
Safety Precautions
Safe-14
1OM-1603
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
The padlock key should be kept in such a way that nobody except the
personnel in charge of maintenance can supervise it.
"4.3" in
"Chapter 2 (Vol. 1)"
The load power to the motors, etc., is turned OFF but the setup
operation must be performed carefully when you put your hand
insidethemachine.Avoidhandandngerinjuries.
"2.3.5" in
"Chapter 3 (Vol. 1)"
"4.1" and "4.2.1" in
"Chapter 6 (Vol. 2)"
Even when the power breaker is set to "OFF", the primary line is
powered, making it possible to cause an electric shock.
Be sure to completely stop the power supply to the machine before
maintenance work.
"1.1" in
"Chapter 1 (Vol. 4)"
Residual voltages may remain behind for a few minutes in the
internal devices of the machine after power interception.
Before performing maintenance work, wait until the charge lamps of
the DC power supply and the servo amplier go "OFF" in 10 minutes
or more after the power breaker is set to "OFF".
"1.1" in
"Chapter 1 (Vol. 4)"
Whentheatringiscut,takecarenottogetinjuredbythe
commercially available cutter.
"3.2.6" in
"Chapter 1 (Vol. 4)"
1108-006
4. Alert Indications in Instruction Manual
Safety Precautions
Safe-15
1OM-1603
1108-004
5. Alert Labels
5. Alert Labels
The alert labels (described below) are used for this machine.
Please read the instructions on each label carefully and check the contents, observing the
actual object.
Be sure to follow the instructions for safety purposes.
These labels should be kept clean and easily legible at a far safe distance.
When a label has deteriorated and become illegible, contact the marketing department or
sales agency of Hitachi High-Technologies for the replacement with a new one.