4OM-1603-007_w.pdf - 第200页

4OM-1603 3-25 3. Error IDs and Remedial Procedures : Chap.3 1 109-006 Error ID Error Name, Description, Cause, and Remedy 420201 Backup(R) Error . The Backup(R) Axis was not completed within predetermined time. Backup ax…

100%1 / 379
4OM-1603
3-24
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
420117 Backup(L) Error
Limit Sensor(-) of Backup(L) axis is detected
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
420118 Backup(L) Error
Disconnecting Motor of Backup(L) axis is detected.
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
420119 Backup(L) Error
Error in the Control Power Voltage of Backup(L) axis
Control power for driver dropped. Check out the Power supply line.(24V Line)
42011a Backup(L) Error
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42011b Backup(L) Error
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42011c Backup(L) Error
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42011d Backup(L) Error
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42011e Backup(L) Error
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42011f Backup(L) Error
System Error of Backup(L) axis
System Error of internal driver. Driver error is supposed if this problem happens
frequently.
420120 Backup(L) Error
Communication Error of the Backup(L) axis
1. Conrmconnectiontocommunicationcable.
2. ConrmPowersupply(24V).
3.ConrmthecommunicationsettingofPCIboard.
4. Conrmtheaddressofdriverandcommunicationratesetting.
420131 Backup(L) Error
Failed to adsorb PCB.
Please check the status of PCB, and perform positioning again.
420132 Backup(L) Error
Failed to adsorb off of PCB.
Please check the status of PCB, and perform to release positioning again.
420133 Backup(L) Error
Adsorb of PCB was off during the production.
Please check the status of PCB, and perform positioning again.
4OM-1603
3-25
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
420201 Backup(R) Error.
The Backup(R) Axis was not completed within predetermined time.
Backup axis is unable to do upward movement and down movement.
The factor is for Motor, Driver, Sensor Error or wiring Error.
Please check the motor, sensor on Machine check screen.
420202 Backup(R) Error.
Driver Alarm on Backup(R) Axis
ConrmresetMethodofdetailedSub-systemerrorcountsofAlarm.
420203 Backup(R) Error.
Error in calculating data of positioning command of Backup(R) Axis
Pleaseconrmthefollowingdata.
1. Machine Offset/Backup Pin(Up/Down)
2. Pattern Program/P.C.B. Information/P.C.B. size/Thickness
3. Control/Common/PRE-PLACED CMPNT THKNS/Bottom of P.C.B.
420204 Backup(R) Error.
Time-over of zeroing of Backup(R) Axis
Check out the dirt, error, disconnection of sensor. If there is no problem with
sensor, the problem could be with motor wire/single error.
420205 Backup(R) Error.
Time-over of the upward movement of stopper(R)
1. PleaseconrmwhetherP.C.B.iscaughtbetweenstopperandconveyor.
2. Error in Up/Down detecting sensor. Please check sensor input.
3. Disconnection/ErrorofOutput.Pleaseconrmthestopperbymanualifsensor
input is correct.
4. Please reset the speed by adjusting speed control when stopper is slow.
420206 Backup(R) Error.
Time-over of the downward movement of stopper(R)
1. ErrorinUp/Downdetectingsensor.Conrmthesensor.
2. Disconnection/ErrorofOutput.Pleaseconrmthestopperbymanualifsensor
input is correct.
3. Please reset the speed by adjusting speed control when stopper is slow.
420207 Backup(R) Error.
Communication Error of the command movement of P.C.B. positioning(Backup)
Motor Driver Error Trouble in communication system(AE-LINK), possibility of Error
of communication P.C.B.(API).
PleaseconrmwiringofcommunicationlineandPowerline.
420208 Backup(R) Error.
Backup Pin/Jig under the conveyor belt is detected.
Check out the interference in Belt on Backup Base does not exist.
420210 Backup(R) Error.
Not ready for System setup of Backup(R) axis
Driver has not completed the parameter setup yet. It is a situation in which a
correct setup has not been received by Communication Error.
Check the Communication Mode, wiring, Power supply of Driver.
4OM-1603
3-26
3. Error IDs and Remedial Procedures : Chap.3
1109-006
Error ID Error Name, Description, Cause, and Remedy
420211 Backup(R) Error.
Error in zeroing in Backup(R) axis
LS, discontinuous zeroing movement, was detected.
Check out the dirt, error of sensor and error in Motor body etc.
420212 Backup(R) Error.
Out-of-Control of Backup(R)
Motor Out-of-Control which is over the width of Out-of-Control detecting occurred.
Please execute all zeroing again, and the restart production.
Please set motor speed slow if it happens frequently. Also, in a case of structure
motor Error.
420213 Backup(R) Error.
Error in motor power voltage of Backup(R) axis
Motor power voltage dropped. Check out the Power supply line(48V Line)
420214 Backup(R) Error.
STP input of Backup(R) Axis is detected
STP input is detected. The function to stop motor by Hard signal.
420215 Backup(R) Error.
Over-current of Backup(R) Axis
Abnormal current in motor output line was detected.
Conrmthemotorwiring,supplyingpower.
420216 Backup(R) Error.
Limit Sensor(+) of Backup(R) axis is detected
+LS signal was detected for moving for (+).
Please check the dirt of +LS sensor, disconnection.
420217 Backup(R) Error.
Limit Sensor(-) of Backup(R) axis is detected
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
420218 Backup(R) Error.
Disconnection Motor of Backup(R) axis is detected
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
420219 Backup(R) Error.
Error in the Control Power Voltage of Backup(R) axis
Control power for driver dropped. Check out the Power supply line.(24V Line)
42021a Backup(R) Error.
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42021b Backup(R) Error.
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42021c Backup(R) Error.
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42021d Backup(R) Error.
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.