4OM-1603-007_w.pdf - 第145页

4OM-1603 2-14 2. Management Information : Chap.2 Management Information Code Display Area A (The outline of the Management Information) Display Area B (The details of the Management Information) 018702 Feeder Alternate I…

100%1 / 379
4OM-1603
2-13
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
018308 Multi-tray (Block2)
ZeroingofTraverse-axisisnotnished.Performzeroingofmulti-tray.
018309 Multi-tray (Block2)
ZeroingofElevator1-axisisnotnished.Performzeroingofmulti-tray.
01830a Multi-tray (Block2)
ZeroingofElevator2-axisisnotnished.Performzeroingofmulti-tray.
01830b Multi-tray (Block2)
Pickup miss cmpnt(8mm) is detected.[B15417]
01830c Multi-tray (Block2)
Pickup miss cmpnt(14mm) is detected.[B15418]
01830d Multi-tray (Block2)
Pickup miss cmpnt(28mm) is detected.[B15419]
01830e Multi-tray (Block2)
Pallet Chuck claw is open.
01830f Multi-tray (Block2)
Pallet Flying away is detected.
018310 Multi-tray (Block2)
Magazine1 (Lower) Shutter on Traverse side is open.
018311 Multi-tray (Block2)
Magazine2 (Upper) Shutter on Traverse side is open.
018312 Multi-tray (Block2)
Access detecting Sensor (Right) : Cannot detect Elevator Unit
018313 Multi-tray (Block2)
Access detecting Sensor (Left) : Cannot detect Elevator Unit
018314 Multi-tray (Block2)
Pick-up miss cmpnt is detected.
018315 Multi-tray (Block2)
Traverse axis is not on origin. Please perform zeroing of multi-tray.
018316 Multi-tray (Block2)
Multi-tray is running. Please operate it after completion.
018317 Multi-tray (Block2)
Please supply Tray Cmpnt after all zeroing.
018401 Multi-tray is not ready to zeroing (Block1)
Execute all zeroing.
018501 Multi-tray is not ready to zeroing (Block2)
Execute all zeroing.
018601 Warning of wiring error
Vacuum Pump 1CB Error
018602 Warning of wiring error
Monitor Error of DC load power
018603 Warning of wiring error
Beam1 CB Error Monitor Error
018604 Warning of wiring error
Beam2 CB Error Monitor Error
018701 Feeder Alternate
Illegal alternate setup of pattern program. Check the settings.
1109-006
4OM-1603
2-14
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
018702 Feeder Alternate
Invalid feeder in alternating. Set feeder valid
018801 XY Origin Offset
Illegal XY-Origin offset of Beam1.
Please retry to send Device data from NT, or execute teaching XY-Origin offset.
018802 XY Origin Offset
Illegal XY-Origin offset of Beam2.
Please retry to send Device data from NT, or execute teaching XY-Origin offset.
018901 Feeder communication
Feeder (Block1) is on communication.
Please wait for a second, and then operate again.
018902 Feeder communication
Feeder (Block2) is on communication.
Please wait for a second, and then operate again.
018a01 Library Feed Pitch check
Library Feed Pitch differs from Feeder. Please check Library and Feeder.(Block1)
018a02 Library Feed Pitch check
Library Feed Pitch differs from Feeder. Please check Library and Feeder.(Block2)
018b01 Library Tape Width check
Library Tape Width differs from Feeder. Please check Library and Feeder.(Block1)
018b02 Library Tape Width check
Library Tape Width differs from Feeder. Please check Library and Feeder.(Block2)
019001 Support Pin
Please move exchange position of support pin.
019002 Support Pin
Noz for exchanging support pin is not set, or Odd type noz is set.
019003 Support Pin
Arranging data in current differs from it of Support Pin of current pattern program.
Please set-up the support pin.
019004 Support Pin
When PCB size 216mm is exceeded, it is impossible to operate if Support pins of
Lane A remain. Please exchange Lane A, or take out it from machine.
019005 Support Pin
It is impossible to do operation for only Lane B because Support Pins of Lane A
remain. Please exchange Lane A, or take out it from machine.
019006 Support Pin
Operation for Lane A is impossible because Support Pins of Lane A have not been
installed. Please exchange Support pins or store them.
019007 Support Pin
It is impossible to do Operation for only Lane A because Support Pins of Lane B
remain. Please exchange Lane B, or take out it from machine.
019008 Support Pin
Support pins of Lane B remain on the base for Support pins of Lane A, so that it is
impossible to do Conveyor width. Please exchange Support pins or store them.
019009 Support Pin
Arrangement of Support Pins interferes in Conveyor. Please retry to arrange it.
1109-006
4OM-1603
2-15
2. Management Information : Chap.2
1109-006
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
01900A Support Pin
"Vacuum/Blower" of Test Operation Mode is set "Disable".
Execute it after cancelling Test Operation Mode.
030162 Operation Requirement
The pattern cannot be switched
030413 Operation Requirement
Specify the order No.
030416 Operation Requirement
ACV server does not pass the authorization.
Please retry to connect to server on a screen [UNIT ADJ]-[ACV Set].
03041c Operation Requirement
ACVCheckError.ComponentIDonthefeederisnotsameasonespeciedby
current program.
030420 Operation Requirement
CommunicationswiththeACVserverisimpossible.AfterconrmingtheACV
server, please retry to perform it. [MAINT]-[UNIT ADJ]-[ACV ADJ].
030430 Operation Requirement
Can not detect Feeder cart(Block1).
Please set Feeder cart to the inside.[B0910, B0911]
030431 Operation Requirement
Can not detect Feeder cart(Block2).
Please set Feeder cart to the inside.[B0910, B0911]
030432 Operation Requirement
The connector of the feeder base (Block1) is not connected to the main body, so
that please connect it. [B0916]
030433 Operation Requirement
The connector of the feeder base (Block2) is not connected to the main body, so
that please connect it. [B0916]
030440 Operation Requirement
The Safety cover is open. Please close it.
030441 Operation Requirement
It is impossible to do Pass Operation without Cart because func of Traceability is
valid. Please restart after setting Option invalid.
030442 Operation Requirement
It cannot run because a simple Cover locked. First, set Stage ready OFF, then set
Stage ready ON.
030450 Operation Requirement
To run is impossible by start protect.
030451 Operation Requirement
Cannot start to run because the output folder on server is disconnected.
Please check output folder setting and the server status of output folder.
030501 Misidenticationatypeofmulti-tray
TheconnectedTrayunit(Block1)doesn'tmatchsettingsofDevice.Pleaseconrm
a type of tray unit, and set it on unit exchange screen.