2OM-1064-002.pdf - 第62页
9910-001 2-50 Tg0247-PM-PM 2. Pattern Program 2.5.5 TRA Y OPERA TION DA T A Display (Option) When the [TRA Y (L) OPN DA T A] key is pressed at the “TRA Y (L) STEPS INFORMA TION” display (Fig. 2.38), the following display…
Fig. 2.40-2
Ref.: [AUTO (LEFT)] and [AUTO (RIGHT)] Keys
“LEFT” or “RIGHT” represents the direction in which a
tray should be pushed when it is set on the pallet.
Any wasteful motion can be suppressed when Tray R is
set at the upper right corner of the pallet and Tray L at the
upper left corner as shown in Fig. 2.41.
Beam B Side
Beam A Side
Tray
Tray
Pallet
Pallet
[AUTO (RIGHT)]
[AUTO (LEFT)]
Fig. 2.41
9910-001 2-49 Tg0247-PM-PM
2. Pattern Program
Case: Tray R
It is recommended that the tray should be set as shown in Fig. 2.40-2 to
ensure the X/Y-beam movable range as wide as possible. In this case, select
the [AUTO (RIGHT)] key.
Magazine
Pallet Drawing Direction
Main Body of Machine
Pallet Supply Direction
Reference Mark (Rivet)
Tray Origin Corner
Matrix Y Direction
Matrix X Direction
Positional Offset X
Beam A Side
X (+)X (-)
Y (-)
Y (+)
FP-5020L
FP-5020R
Tray Traverse
Pallet
Tray L (Upper
Left Corner)
Pallet
Tray R (Upper
Right Corner)
Beam A Side
9910-001 2-50 Tg0247-PM-PM
2. Pattern Program
2.5.5 TRAY OPERATION DATA Display (Option)
When the [TRAY (L) OPN DATA] key is pressed at the “TRAY (L) STEPS
INFORMATION” display (Fig. 2.38), the following display appears on the
screen.
While the tray L information is being edited, the “TRAY (L) OPERATION
DATA” display appears on the screen.
While the tray R information is being edited, the “TRAY (R) OPERATION
DATA” display appears on the screen.
Fig.2.42
MAGAZINE ALTN
“ENABLE” or “DISABLE”can be set in the data box to determine whether
or not the magazine alternate function should be used.
[ENABLE] : The magazine alternate function becomes valid.
[DISABLE] : The magazine alternate function does not work.
About the magazine alternation function
When this function is used, components can be supplied during automatic
operation without stopping the machine.
STEPS # OFFSET
The steps # offset value can be entered in the data box.
Steps # Offset
This offset data is used to shift the current feeder (currently allocated com-
ponents) to the multi-layer tray feeder.
Based on the FDR No. and the component data indicated in the placement
data, the current feeder position is shifted as much as this offset.
9910-001 2-51 Tg0247-PM-PM
2.5.6 OFFSET X AUTO SETTING Display (Option)
When the [OFFSET X AUTO SET] key is pressed at the “TRAY (L) STEPS
INFORMATION” display (Fig. 2.38), the following display appears on the
screen.
While the tray L information is being edited, “OFFSET X AUTO SETTING”
display for Tray L appears on the screen.
While the tray R information is being edited, “OFFSET X AUTO SETTING”
display for Tray R appears on the screen.
2. Pattern Program
Fig. 2.43
As the values for the tray position offset “X (mm)” change depending on whether
or not “AUTO (LEFT)” or “AUTO (RIGHT)” is set for the tray in each step
(the tray to be specified as a multi-layer tray), it is required to set the offset
values for each individual trays.
That is, the offset values X (design values) can be set by selecting either the
[AUTO (LEFT)] or the [AUTO (RIGHT)] key.
When the [SELECT ALL STEP] key is pressed, the offset values X in all steps
can be entered automatically.