2OM-1064-002.pdf - 第72页
• T o designate the pick-up priority (“2” to be set as “S” data) Desi gnati on Possi ble Desi gnati on Impo ssibl e • Pairin g of Com ponents betwee n T a pe Feede r s • Pairin g of Com ponents betwee n T a pe and V ib r…
• To designate the simultaneous pick-up (“1” to be set as “S” data)
Designation Possible Designation Impossible
• A pair of components which meet the following
requirements
• Pairing Components between Tape Feeders
• The distance between two picked
components is “108 mm”.
(Based on the distance (108 mm) between
the nozzle rotational centers of Heads #1 and
#2)
Example:
Using the 8 mm tape feeder
Lane Pitch (18 mm) × 6 Lanes =
108 mm
Refer to “7. Construction of Feeder Carriage
of Section 1 in Volume 1” for the
combination of the tape feeders.
• Either one of the data to be paired is the
component of the vibratory stick feeder.
• Pairing of Components between Vibratory
Stick Feeders
• Pairing of Components between Vibratory
Stick and Tape Feeders
•
Pairing
of Components between Vibratory
Stick and Step-Stacking Stick Feeders
(Reserved Function)
• Either one of the data to be paired is the
component of the step-stacking stick feeder.
(Reserved Function)
• Pairing of Components between Step-
Stacking Stick Feeders
• Pairing of Components between Step-
Stacking Stick and Tape Feeders
• Pairing of Components between Step-
Stacking Stick and Vibratory Stick Feeders
• Eccentric Pick-Up Designated Components
(Chuck Location Adjustment X and Y in
Component Library Data)
• Components for which “ADHESIVE” is set in
the “CARRIER TYPE” data box in the
component library data
• Pairing of Components between Tray Feeders
• The distance between two components to be
supplied is not “108 mm”.
9910-001 2-59 Tg0247-PM-PM
2. Pattern Program
• To designate the pick-up priority (“2” to be set as “S” data)
Designation Possible Designation Impossible
• Pairing of Components between Tape Feeders
• Pairing of Components between Tape and
Vibratory Stick Feeders
• Pairing of Components between Tape and Step-
Stacking Stick Feeders (Reserved Function)
• Pairing of Components between Tape and Tray
Feeders (Only Beam A Side)
• Pairing of Components between Vibratory Stick
Feeders
• Pairing of Components between Vibratory Stick
and Step-Stacking Stick Feeders (Reserved
Function)
• Pairing of Components between Vibratory Stick
and Tray Feeders (Only Beam A Side)
• Pairing of Components between Step-Stacking
Stick Feeders (Reserved Function)
• Pairing of Components between Step-Stacking
Stick and Tray Feeders (Only Beam A Side)
(Reserved Function)
• Pairing of Components between Tray Feeders
(Only Beam A Side)
• Eccentric Pick-Up Designated Components
(Chuck Location Adjustment X and Y in
Component Library Data)
• Components for which “ADHESIVE” is set in
the “CARRIER TYPE” data box in the
component library data
• Both components belong to the same area where
only one head can pick them up.
(Such components cannot be picked up by the
counteractive head because only the left head
can be used for the 6 lanes at the left end and
only the right head for the 6 lanes at the right
end.)
• Pairing of a component located at one side of the
X/Y beam and a component at the other side
2. Pattern Program
9910-001 2-60 Tg0247-PM-PM
V
[Setting of Repetitive Patterns]
When multi-unit P.C.B.’s (repetitive patterns) are used and the P.E.C. rec-
ognition function is implemented on each unit P.C.B., set “01” or “02” in
the text field labeled “V” of P-0000 step.
00: B.B.R. P.E.C. Recognition Function “OFF”
01: B.B.R. P.E.C. Recognition Function “ON” (1-Point Recognition)
02: B.B.R. P.E.C. Recognition Function “ON” (2-Point Recognition)
• When a recognition mode is specified, the coordinates of mark position
and mark data can be set in the V-0000 step of the placement data (V).
Ref.: As both V data shown at the placement data (P) and (V) displays
are the same, the V data can be entered at either display.
[Setting of Each Individual Placement Points]
Set each individual placement points in the text field labeled “V” of the
placement step.
00: P.E.C. Recognition “OFF”
01: P.E.C. Recognition “ON” (1-Point Recognition)
02: P.E.C. Recognition “ON” (2-Point Recognition)
Note: Set “ON” in the “P.E.C. RECOGNITION” data box and in the “LO-
CAL” data box of the label “P.E.C. RECOGNITION MODE” at the
“OPERATION DATA” display.
2. Pattern Program
9910-001 2-61 Tg0247-PM-PM