YSM20R_YSM20WR_Ope_E.pdf - 第102页
Chapter 2 Basic operation Contents 1. Before operation 2-1 1.1 Canceling emergency stop 2-1 1.2 Clearing an error 2-2 1.3 Typical err ors and troubleshooting 2-3 2. Operation screen and buttons 2-8 2.1 Basic configuratio…
1-68
1
Unit names and functions
8.3 UPS (Uninterruptible Power Supply)
n
Purpose of UPS
1. Preventing data destruction
In the event of unexpected power shutdown such as power blackout, the user data including board data saved in the
machine may be damaged. A machine with a UPS (uninterruptible power supply), however, backs up the control power
supply to the control box and power supply to the monitor display at the time of power blackout. The machine can be
safely shut down without damaging the user data.
2. Resuming automatic operation without going through the restart procedure
A machine with a UPS can resume the automatic operation without going through the restart procedure in the event of a
power failure of short period of time such as momentarily power failure. If the UPS detects power shutdown, the UPS
continues to supply electrical power to the control box even if the machine gets into the state of emergency stop. Thus,
the machine resumes the automatic operation immediately after the power supply restores.
n
NOTE
The UPS can back up the power supply for a limited period of time. If the duration of power shutdown continues more
than 60 seconds, the machine automatically shuts itself down.
n
UPS installation location
The UPS is installed below the extension conveyor on the front right.
n
NOTE
UPS can be installed only on the machine that has an extension conveyor.
UPS
UPS
UPS installation position
Extension conveyor
23137-KMK-00
n
NOTE
For replacing the UPS battery, refer to the “YSM20R Maintenance Manual”. For more details about handling the UPS,
refer to the option manual “UPS (Uninterruptible power supply)” or the operation manual issued by the manufacturer.
Chapter 2 Basic operation
Contents
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
2. Operation screen and buttons 2-8
2.1 Basic configuration of operation screen 2-8
2.2 Setup screen 2-12
2.3 Unit screen 2-14
3. Displaying the production monitors 2-22
3.1 Production 2-22
3.2 Main 2-24
3.3 Vision 2-26
3.4 Alignment 2-28
3.5 Retry 2-29
3.6 Fiducial 2-30
3.7 Badmark 2-31
3.8 Pick Pos. (Pickup position offset) 2-32
3.9 Force 2-34
3.10 Pick Rate Warning 2-35
3.11 Schedule task 2-38
3.12 Nozzle health check 2-39
3.13 Coplanarity checker 2-41
4. Preparing component tape 2-42
4.1 Tape feeders 2-42
4.1.1 Setting component tape 2-42
4.1.2 Setting feeders on the feeder exchange carriage 2-49
4.1.3 Attaching the feeder exchange carriage on the mounter 2-54
4.1.4 Setting board data of component tape 2-56
4.1.5 Disposing of used cover tape and carrier tape 2-62
4.1.6 Detaching the feeder exchange carriage 2-65
4.1.7 Detaching the feeder 2-66
4.1.8 Detaching component tape 2-68
5
.
Preparing tray component supply unit 2-70
5.1 Starting and ending the tray component supply unit 2-70
5.2 Setting tray components on pallet 2-71
5.2.2 Setting the component trays on the pallet 2-73
5.3 Setting the pallet in the magazine 2-74
5.3.1 Setting the number of pallets to be stored 2-74
5.3.2 Setting the pallet in the magazine 2-76
5.4 Exchanging magazine 2-78
5.5 Exchanging pallet 2-82