YSM20R_YSM20WR_Ope_E.pdf - 第140页

2-37 2 Basic operation • Nozzle MACS Displays the nozzle MA CS status. n NOTE The nozzle MACS is a function that detects the position of the nozzle set up on a head to per form pickup offset correction. Similar to the fe…

2-36

Basic operation

• Parts name

Displays the component name.

• Tape Type

The “Tape Type” shows the type of tape when the machine processes component tapes. It shows the method of supplying

components when processing tray components.

• Pick Rate (%)

Displays the pickup rate for each component. Rate is calculated by the following formula.

1 – ([Error count] ÷ [Number of components used]) = Pickup rate

• Feeder MACS

Displays the feeder MACS status.

• Offset X(mm), Y(mm)

Displays the offset amounts of the feeder MACS.

NOTE

The feeder MACS is a function that recognizes the mark at a speciﬁc location on the feeder to perform pickup offset

correction. This function normally applies to picking up components of 1005 or smaller.

[Head Info] tab

Monitor: Pick Rate Warning

Head info

24221-KMK-00

• Table

Displays the corresponding table. This machine shows “Table A”.

• Head No.

Displays the head No. being used.

• Nozzle Type

Displays the current nozzle type.

• Head Type

Displays the method of changing the nozzle currently in use and other particulars such as automatic nozzle change and

manual nozzle change.

• Pick Rate (%)

Displays the pickup rate for each head. Rate is calculated by the following formula.

1 – ([Error count] ÷ [Number of components used]) = Pickup rate

2-37

Basic operation

• Nozzle MACS

Displays the nozzle MACS status.

NOTE

The nozzle MACS is a function that detects the position of the nozzle set up on a head to perform pickup offset

correction. Similar to the feeder MACS, this function applies to the nozzles that pick up components of 1005 or smaller.

• Center XY(mm), Offset XY(mm)

Displays the offset amounts of the nozzle MACS.

• [Current Check] button

Selecting a component (row) from among components with abnormal pickup rates (rows shown in "red") and clicking this

button sets "watch-and-wait" mode for that component.

• [All Check] button

Clicking this button sets "watch-and-wait" mode for all components with abnormal pickup rates (rows shown in "red").

"Watch-and-wait" mode

The "watch-and-wait" mode is such that, if a pickup error occurs with a component, pressing the [Current Check] button

or the [All Check] button makes the machine system memorize the pickup rate at that point. After that, the machine

indicates by the color changes whether the pickup rate improves or worsens.

For example, after an abnormal pickup rate is stored in "watch-and-wait" mode, if the problem is eliminated and

operation resumed, and the pickup rate improves, then the color of the row(s) changes from "pink" to "yellow" to show an

improvement has been made. Conversely, if the pickup rate becomes even worse, then the color changes from "pink"

back to "red" to show the troubleshooting was ineffective.

The colors in the following graph show changes in the pickup rate, using an example when "caution (yellow)" is set to

99.00% and "warning (red)" to 95.00%.

Color transitions per changes in pickup rates

100

Pickup rate %

Time

Changes to yellowStart (white)

Changes to yellow (better pickup rate)

Changes to red

(worse pickup rate)

Pressing the [Current Check] or [All Check] button enables

"watch-and-wait" mode and changes the color of "red" row(s) to

"pink".

23201-KMK-00

2-38

Basic operation

3.11 Schedule task

When executing the schedule tasks such as the “Vacuum Check” or the “Nozzle Tip Cleanliness Check”, this

screen shows the results.

The display contents are updated after each schedule task has been completed. Additionally, the error

information by head and information showing the execution results are recorded into the history.

Monitor : Schedule task

Execution

result list

Arrow mark

Manual operation button

Page number

display

24222-KMK-00

• Check Contents

Change the schedule task type to be displayed from the full-down list.

Target : "Vacuum Check" "Nozzle Tip Dirt Check" "Nozzle Shaft Cleaning Blow" "Nozzle Shape Check"

"Nozzle Alignment Check"

• Schedule Task Last Date

Displays the last date and time when the schedule task was executed.

• Execution result list

Displays the schedule task execution result.

OK : Schedule task is completed successfully.

NG/Error : Schedule task is terminated abnormally.

Blank : Schedule task is not implemented.

TIP

The list shows tables (head units) A through D. However, this machine shows values in A Table and B only.

• Nozzle Type

Displays the nozzle type, for which the schedule task is executed.

• Arrow mark

Change multiple nozzle type displays.

• Page number display

Displays the current page number and maximum page number. This page number is not displayed when there is only one

page.

• Manual operation button

Allows you to manually execute the schedule task, such as “Cleaning Blow (Nozzle shaft cleaning blow)”, “Tip Dirt

Check”, “Vacuum Check”, “Buffing Check”, “Shape Check” and “Alignment Check”.