YSM20R_YSM20WR_Ope_E.pdf - 第66页
1-33 1 Unit names and functions n Feeder removing conditions 1. When Setting the "Skip Retr y" If setting the skip retry , the parts of the feeder occurring the parts run-out will be mounted at the end and othe…
1-32
1
Unit names and functions
4.3.2 Non-stop feeder change
If activating "ZSF Nonstop Parts Supply setting*" with the combination of the feeder exchange carriage for ZS
feeder and ZS feeder, the feeder satisfying the removing conditions can be changed without stopping the
machine. Additionally if the setting is activated, ZS feeder not used for mounting can be removed and inserted
even during operation.
n
Summary of the non-stop feeder change conditions
Using the feeder exchange carriage for ZS feeder and ZS feeder
*<Non-stop feeder change setting> is enabled. * <Setting> is disabled.
Feeder in use
Feeder satisfying
removing conditions
Feeder not in use Feeder in use Feeder not in use
Mounter is operating. Not available Available Available Not available Not available
w
WARNING
AS ZS FEEDER IS REMOVED DURING OPERATION, A SPACE IS FORMED. HOWEVER, NEVER PUT YOUR HAND IN THIS SPACE.
DOING SO MAY CAUSE SERIOUS HAZARD.
c
CAUTION
When pulling the feeder, make sure to pull it completely and insert it after cutting the carrier tape. If pulling the feeder
incompletely and insert it, the carrier tape is raised and it may interfere with the head.
n
Non-stop feeder change setting
Setting non-stop feeder change
“Machine Information” - ”Installation Setting” screen
ZSF Nonstop Parts Supply : ENABLE / DISABLE
24110-KMK-00
n
About handling of SS feeder
The feeder exchange carriage for ZS feeder is applicable with SS feeder as well.
But since it is necessary to open the safety cover for replacing SS feeders, non-stop feeder change function is not
available.
1-33
1
Unit names and functions
n
Feeder removing conditions
1. When Setting the "Skip Retry"
If setting the skip retry, the parts of the feeder occurring the parts run-out will be mounted at the end and other normal
parts will be mounted prior to them. At this time the message "Ea30151 Parts empty (Continue to Run)" will be displayed
on the screen and the corresponding feeder can be removed. The LED of the removable feeder glows yellow.
2. When pressing the [Feeder Remove] button
If activating the non-stop feeder change setting, the [Feeder Remove] button will be displayed on the "Monitor" -
"Production" screen. The message "Ea30152 Ready to remove the feeder." will be displayed by selecting any feeder and
pressing the [Feeder Remove] button. Then the feeder will be removable. Same as the skip retry setting, the selected
feeder parts will be mounted at the end and other normal parts will be mounted prior to them.
n
NOTE
Regarding both cases above, if the parts of the removed feeder are mounted before completing the parts refill, an
error occurs and the machine stops.
3. When setting the alternative component function
If setting the alternative component function, the feeder occurred the parts run-out will be replaced to the other feeder
that the alternative component function is set and it continues to mount. At this time the message "Ea30151 Parts empty
(Continue to Run)" will be displayed on the screen and the corresponding feeder can be removed. The LED of the
removable feeder glows yellow. Additionally, if refilling components to the removed feeder and setting it to the machine
again, the component supply is changed to the feeder that has been set again.
1-34
1
Unit names and functions
Feeder removing conditions : 1. Setting "Skip Retry"
1
Open the "Board" tab screen.
Press the [Board] button and select the "Board" tab.
2
Set the "Skip Retry".
Select "Use" from the "h. Skip Retry" drop-down list.
Using skip retry
[Board] - [Board] screen
h : Skip Retry
Select” Use”
24111-KMK-00
3
Activate the setting.
The changed setting is activated by saving the board data and reloading it.
n
Operation when skip retry is activated
When running out components, the following message appears. The operation continues.
The LED of ZS feeder that can be detached glows yellow.
Parts empty (Continue to Run) screen
24112-KMK-00