YSM20R_YSM20WR_Ope_E.pdf - 第24页

General Contents About this manual 1. Using this manual i Manual Classifications / Contents i 2. Contents of each chapter ii 3. Page layout iii Chapter 1 Unit names and functions 1. Machine main unit 1-1 2. Operation pan…

100%1 / 229
xxi
Safety instructions
4. Safety message in this manual
The contents that must be followed to prevent users and third parties from injury and damage to a machine
are explained as "Warning" and "Caution" in this manual. The contents that are required and helpful
information when operating a machine are explained as "Note" and "Tips".
n
Warning
w
WARNING
INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.
THESE ARE POINTS MOST ESSENTIAL FOR PROTECTING THE SAFETY OF THE MACHINE OPERATOR, INSPECTOR AND SERVICE
PERSONNEL.
n
Caution
c
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury, or material loss or damage
to the machine. These points are important for protecting the safety of the machine and data, etc.
n
Note
n
NOTE
Provides required information when operating a machine in a simple and clear manner.
n
Tip
TIP
Provides helpful explanation for work.
n
Emergency stop
e
EMERGENCY STOP
IF THIS MARK IS IN THIS MANUAL, MAKE SURE TO WORK WHILE A MACHINE IS IN EMERGENCY STOP.
General Contents
About this manual
1. Using this manual i
Manual Classifications / Contents i
2. Contents of each chapter ii
3. Page layout iii
Chapter 1 Unit names and functions
1. Machine main unit 1-1
2. Operation panel and data input unit 1-7
2.1 Operation display screen 1-7
2.2 Keyboard (option) 1-8
2.3 Operation panel buttons 1-9
3. Head unit 1-10
3.1 Component pick-and-place head 1-11
3.1.1 HM Head unit 1-11
3.1.2 FM Head unit 1-12
3.2 Nozzle types 1-13
3.2.1 HM Head / FM Head nozzles 1-13
3.3 Nozzle station (option) 1-14
3.3.1 HM Head nozzle station 1-14
3.3.2 FM Head nozzle station 1-15
3.4 Blow station 1-16
3.4.1 Shaft-blow function 1-16
3.4.2 Manual nozzle shaft blow procedure 1-17
3.4.3 Automatic nozzle shaft blow procedure 1-21
3.4.4 Shaft blow dump of very small components 1-24
4. Component supply section 1-25
4.1 Machine layout 1-25
4.2 Supply from fixed feeder bank 1-27
4.2.1 70-reel fixed feeder bank 1-27
4.2.2 Reel holder (option) 1-28
4.3 Supply from feeder exchange carriage 1-29
4.3.1 Feeder exchange carriage 1-29
4.3.2 Non-stop feeder change 1-32
Feeder removing conditions : 1. Setting "Skip Retry" 1-34
Feeder removing conditions : 2. Pressing [Feeder Remove] button 1-35
Feeder removing conditions : 3. Setting alternative component function 1-36
4.4 Tray component supply unit (option) 1-39
EPKMK-207-0300
5. Conveyor 1-40
5.1
Conveyor unit 1-40
5.2 Sensor layout of conveyor unit 1-47
5.3 Board position in machine by conveyor type/board size 1-54
6. Recognition unit 1-56
6.1 Fiducial, Scan and Side-view camera 1-56
6.2 Side-view function (Scan camera / Side-view camera) 1-57
6.3 Multi-view cameras 1-58
7. Axis configuration 1-59
7.1 Head unit axis configuration 1-59
7.2 X/Y-axis and conveyor axis configuration 1-61
8. Other options 1-64
8.1 Coplanarity checker 1-64
8.2 Ionizer 1-65
8.3 UPS (Uninterruptible Power Supply) 1-68
Chapter 2 Basic operation
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
2. Operation screen and buttons 2-8
2.1 Basic configuration of operation screen 2-8
2.2 Setup screen 2-12
2.3 Unit screen 2-14
3. Displaying the production monitors 2-22
3.1 Production 2-22
3.2 Main 2-24
3.3 Vision 2-26
3.4 Alignment 2-28
3.5 Retry 2-29
3.6 Fiducial 2-30
3.7 Badmark 2-31
3.8 Pick Pos. (Pickup position offset) 2-32
3.9 Force 2-34