EUKYX-199-3100_G5S2_Instruction_Vol3_E.pdf - 第149页

EUKYX 2-1 199-3100 1. Menus for System Setting 1 . Men u s for S ys t em Settin g Graphic Development Cover F3B1A "S ys. Sett ing " M ain Menu B ar The fol lowi ng buttons are arra nged and used to open the op …

199-3100

Chapter 2

System Settinge

This chapter describes the functions and operations related to the

machine system setup data, the nozzle data, machine setup, etc.

1. Menus for System Setting

2. Offset Data

3. Auto Operation

4. MACH SETUP

5. Password Setting

6. Mon. Adj

EUKYX

2-1199-3100

1. Menus for System Setting

Graphic

Development

Cover

F3B1A

"Sys. Setting" Main Menu Bar

The following buttons are arranged and used to open the operation windows and set up the system

environment.

Button Description

Offset Sets various kinds of offset data for positional adjustment and

accuracy of each device section related to machine operation.

Ope. Palam. Sets various parameters related to automatic operation of the

machine and check the machine performance, production rate,

production guidance, etc.

Mach Set Sets the screen saver function, specify the unit of length,

enable or disable the data editing under production operation,

the light tower, and the buzzer.

Password Sets a password and the scope of authority according to the

given authority.

Mon. Adj. Performs the monitor screen adjustment.

EUKYX

2-2199-3100

2. Offset Data

Pressing [Sys. Setting] - [Offset] buttons displays the following window.

Graphic

Development

F3B2

Do not change the parameters unless necessary. These parameters are factory-adjusted upon

shipment of the machine.

The Offset data is provided with the windows below and displayed by pressing relevant button.

Tab Description

Device Offset Adjusts the positional and angular deviations based on the design dimensions

representing the X/Y beam driving X/Y coordinates viewed from the PCB positioning

X/Y coordinates.

Feeder Base Adjusts the deviations based on the design values of each individual feeders.

FeederA This offset data is used independently for the machine. The corresponding tab sheet

enables the operator to adjust the positional deviations (viewed from the PCB

positioning X and Y coordinates) based on the design dimensions representing the

feeder pickup position and height for each individual feeder slot Nos. (Fdr Nos.).

FeederB Corrects the variations, etc., for each individual feeders.

Beam Corrects the positional and angular deviations based on the design dimension (the

distance between the placement reference coordinate origin and the center of the PEC

recognition camera at the head origin).

Head Corrects the positional deviation (placement coordinates) caused due to the deviation

of straightness (skew) of each individual head up/down axis guides and set up the

offset data for the distance between the scanning coordinate center of the PEC

camera and the head rotational center.

Nozzle Adjusts the deviations in height and rotational center of each nozzle and set the

measured values of the master nozzle (reference nozzle).

Nozzle Stocker Sets the offset data for adjustment of positional deviations compared with the design

dimensions of the nozzle stocker unit position (viewed from the PCB positioning

reference) and the offset data for adjustment of positional deviations compared with

the design dimensions (viewed from the PCB positioning reference) for each individual

addresses 1 through 15 of 1-1 to 2-2.

PCB Recog Adjusts the horizontal swing (tilt) of the PEC recognition camera.

Comp. Recog Sets the offset data that will be used to adjust the positional deviation based on the

design dimension (the distance between the machine reference coordinate origin and

the center of the component recognition camera).

Table Sets the amount of deviation based on the specified distance when each head (Heads

1 through 2) has moved as far as the specified distance (each grid point) from the

PCB positioning reference.

Unit Offset Used when the multi-layer tray feeder is used.

Note: Refer to "GS-FP600 Multi-Layer Tray Feeder" for details.

Place Pos Table

This offset data corrects the feed inaccuracy of the X/Y axis of the placement position.

Notice