EUKYX-199-3100_G5S2_Instruction_Vol3_E.pdf - 第85页

EUKYX 1-36 199-3100 5.7 Cmp Recog Mag 5. 7 Cmp Recog Mag The correspondi ng wi ndow en ables y ou to perform a teach in g operation on the m agn ifica tion of the Component recogn ition ca mera. [1] [2] Graphic Developme…

EUKYX

1-35199-3100

5.6 MARK LIGHT

[1]

[2]

Graphic

Development

F3A32

[1] Teaching Data Display Section

Displayed are the offset data items for each reference mark for the designated camera.

[2] Teaching procedures section

The following buttons are arranged in teaching procedures section.

Select camera

Selects the camera in the block to be taught.

[Teach Start] button

Starts the teaching.

[Save] button

The teaching results are saved.

• Teaching Procedure

(1) Select the component recognition camera for which the teaching is performed, in the

"Select Camera" section.

(2) Press the [Teach Start] button. (In a single teaching operation, the marks in the rear and

front of the designated component recognition camera are taught one by one).

(3) Press the [Save] button.

Procedure

EUKYX

1-36199-3100

5.7 Cmp Recog Mag

The corresponding window enables you to perform a teaching operation on the magnification of the

Component recognition camera.

[1]

[2]

Graphic

Development

F3A33

[1] Teaching Data Display Section

Displayed are the magnifications for the designated camera and head.

[2] Teaching procedures section

The following buttons are arranged in teaching procedures section.

Select camera

Selects the component recognition camera to be taught.

Select head

Selects the head whose component recognition camera is taught.

[Jig Attach] button

The head is moved to the position where the magnification teaching glass jig is easily

attached.

[Teach Start] button

Starts the teaching. Based on the captured image, the magnification offset for the component

recognition camera is calculated.

[Jig Colct] button and [Vac OFF] button

The head is moved to the position where the magnification teaching glass jig is easily

removed.

[Save] button

The teaching results are saved.

EUKYX

1-37199-3100

5.7 Cmp Recog Mag

• Component Recognition Camera Magnification Teaching Jig

For the component recognition camera magnification teaching, the following jig is used.

Magnification Teaching Glass Jig JG-0084

(KYF-M8673-00, Component Recognition Calibration Jig)

On the bottom surface of the jig component, 576 black circles with

1.00 [mm] are vapor-deposited

at 2.00 [mm] pitch.

50 mm

F3A34

Jig Pick-up Nozzle

For the pick-up of the magnification teaching glass jig, the nozzle VF02 for middle-size odd shaped

nozzle is used.

• Component Recognition Camera Magnification Teaching Procedure

(1) Press the Camera and Head selection buttons and select the camera and head to be taught.

The teaching operations for four combined patterns are performed.

Camera 1 – Head #1 / Camera 1 – Head #2 / Camera 2 – Head #1 / Camera 2 – Head #2

(2) Press the [Jig Attach] button and within 10 seconds, press the [START] button on the

operation panel. (The head will move to the position where the magnification teaching

glass jig is to be picked up (jig attachment position)).

(3) Setup the nozzle VF02 for middle-size odd shaped nozzle onto this end of the head moved

to the jig setup position and pick up the magnification teaching glass jig so that the image

is within the recognition area.

When the jig is to be picked up using the nozzle, hold the right and left ends of the jig to pick it up.

When the vacuum pump is not activated, cancel the test operation mode or remove a check

mark from the item for vacuum pump stop on the test operation mode window.

(4) Press the [Teach Start] button. (Based on the captured image, the magnification offset for

the component recognition camera will be calculated.)

(5) Press the [Jig Colct] button and within 10 seconds, press the [START] button on the

operation panel. (The beam will move to the position where the magnification teaching

glass jig can be removed).

(6) Remove the magnification teaching glass jig.

(7) Press the [Vac OFF] button to turn off the vacuum and remove the nozzle used for the teaching.

(8) Press the [Save] button to save the teaching results.

Procedure

Note

Notice