PathMaster-REV-L-4.5-1.pdf - 第167页
Machine Operati on Manual Revision L / February 2020 Page 167 of 20 0 Appendix A - Table of Figures Figure 1: P athMaster® Installation Administrator Priv ileges Window ......................................... 16 Figure…
Machine Operation Manual
Revision L /
February 2020
Page 166 of 200
Warranty
PVA Warranty Policy
PVA warrants the enclosed product against defects in material or workmanship on all
components for one year from the date of shipment.
The warranty does not extend to components damaged due to misuse, negligence, or
installation and operation that are not in accordance with the recommended factory
instructions. Unauthorized repair or modification of the enclosed product, and/or the use
of spare parts not directly obtained from PVA (or from factory authorized dealers) will void
all warranties.
All PVA warranties extend only to the original purchaser. Third party warranty claims will
not be honored at any time.
Prior to returning a product for a warranty claim, a return authorization must be obtained
from PVA’s Technical Support department. Authorization will be issued either via the
telephone, facsimile, or in writing upon your request.
To qualify as a valid warranty claim, the defective product must be returned to the factory
during the warranty period. Upon return, PVA will repair (or replace) all components found
to be defective in material or workmanship.
(Retain this for your records)
Product Information:
PRODUCT: ______________________________
SERIAL NUMBER: ______________________________
DATE OF PURCHASE: ______________________________
Machine Operation Manual
Revision L /
February 2020
Page 167 of 200
Appendix A- Table of Figures
Figure 1: PathMaster® Installation Administrator Privileges Window ......................................... 16
Figure 2: PathMaster® Installation UAC Window ............................................................................. 16
Figure 3: Example Startup Validation Warning ................................................................................. 17
Figure 4: Calibration Plate .................................................................................................................... 20
Figure 5: PathMaster® Window .......................................................................................................... 22
Figure 6: Upper Status Bar................................................................................................................... 22
Figure 7: Lower Status Bar ................................................................................................................... 22
Figure 8: Programming Toolbar .......................................................................................................... 23
Figure 9: Explanation of Functions .................................................................................................... 23
Figure 10: Legacy Mode, DMC2000 Toolbar ..................................................................................... 25
Figure 11: Run Commands .................................................................................................................... 25
Figure 12: Run Fiducials / Surfaces Status Colors .......................................................................... 26
Figure 13:Run Selection / Sequence Status Colors ......................................................................... 27
Figure 14: Backup Files ......................................................................................................................... 28
Figure 15: BDE Administrator .............................................................................................................. 29
Figure 16: BDE Administrator Select Directory ............................................................................... 29
Figure 17: Save for Part Manager ......................................................................................................... 31
Figure 18: Export Machine Transfer ................................................................................................... 33
Figure 19: Import Machine Transfer ................................................................................................... 33
Figure 20: Example Export Error ......................................................................................................... 34
Figure 21: Example Import Error ......................................................................................................... 34
Figure 22: PathMaster® Opened through Portal ............................................................................ 35
Figure 23: Select Project Window ....................................................................................................... 36
Figure 24: Select a Project ................................................................................................................... 36
Figure 25: Setup Machine Parameters ............................................................................................... 37
Figure 26: MAIN Program Change Conformation ............................................................................ 37
Figure 27: Dispensing Parameters ..................................................................................................... 38
Figure 28: Move Parameters ................................................................................................................ 39
Figure 29: Units and Machine Type .................................................................................................... 40
Figure 30: Changes in Options When the Teach Tool Box is Selected ........................................ 41
Figure 31: Changes in Options When the Teach Tool Box is Selected ........................................ 42
Figure 32: Machine Parameters, Tools Section Options ................................................................ 43
Figure 33: Tool Routine Configuration .............................................................................................. 43
Figure 34: Needle Calibration .............................................................................................................. 43
Figure 35: Needle Calibration Setup Window ................................................................................... 44
Figure 36: Tool Selection ...................................................................................................................... 44
Figure 37: Use Needle Calibration Checkbox ................................................................................... 45
Figure 38: Profile Tool Type and Profile Type Selection ................................................................ 46
Figure 39: Height Profiling ................................................................................................................... 46
Figure 40: Profile Calibration Setup ....................................................................................................47
Machine Operation Manual
Revision L /
February 2020
Page 168 of 200
Figure 41: Workspace Reference ........................................................................................................ 48
Figure 42: Workspace Reference Window ........................................................................................ 48
Figure 43: Select the Z Position .......................................................................................................... 49
Figure 44: Tool Name and Configuration .......................................................................................... 50
Figure 45: Sort Options .......................................................................................................................... 51
Figure 46: Add a Virtual Tool ............................................................................................................... 52
Figure 47: Select Virtual Tool and Delete .......................................................................................... 53
Figure 48: Delete Tool Window ............................................................................................................ 53
Figure 49: Tool Configuration .............................................................................................................. 54
Figure 50: Teach Tool Configuration ................................................................................................. 55
Figure 51: Tool Offset Button .............................................................................................................. 56
Figure 52: Teach Tool, Tool Reference ............................................................................................... 57
Figure 53: Run Tool Reference Training Window ............................................................................. 57
Figure 54: Dot Drop Mode .................................................................................................................... 58
Figure 55: Tool Change Button ........................................................................................................... 59
Figure 56: Tool Selection Window ...................................................................................................... 60
Figure 57: Tool Offset Window ............................................................................................................ 60
Figure 58: Tool Calibration .................................................................................................................... 61
Figure 59: Tool Selection Window ....................................................................................................... 61
Figure 60: Calibration Wait Screen ..................................................................................................... 62
Figure 61: Calibration Status Screen ................................................................................................. 62
Figure 62: Machine Auxiliary ............................................................................................................... 63
Figure 63: Auxiliary Code ..................................................................................................................... 63
Figure 64: Communications ................................................................................................................ 64
Figure 65: Program Table ..................................................................................................................... 66
Figure 66: Playback ................................................................................................................................ 67
Figure 67: Example Edit Window ......................................................................................................... 68
Figure 68: Tool Selection ...................................................................................................................... 68
Figure 69: Teach Pendant .................................................................................................................... 70
Figure 70: Example Fiducial .................................................................................................................. 71
Figure 71: Normal Space ........................................................................................................................ 73
Figure 72: Corrected Space ..................................................................................................................74
Figure 73: Teach Fiducials .....................................................................................................................74
Figure 74: Fiducial Window ................................................................................................................... 75
Figure 75: Edit Fiducial ........................................................................................................................... 75
Figure 76: Global Offset and Skew ...................................................................................................... 75
Figure 77: Comment ............................................................................................................................... 77
Figure 78: DMC Command Programmed ............................................................................................ 77
Figure 79: Edit DMC................................................................................................................................. 77
Figure 80: Plugin Select Menu .............................................................................................................78
Figure 81: Plugin Select .........................................................................................................................78
Figure 82: Example Plugin Window ..................................................................................................... 79