2OM-1075-002.pdf - 第152页

AHB01ESPP Pickup Level for TIM-5000 Series Because the distance between the reference level of the em- bossing and the pickup surface must be entered, it is required to make the manual calculation (Principal Pickup Level…

AHB01ESPP

*8 "Nozzle Polarity Mode" Group Box

When the same library data is used for both Sides A and B, it can be

determined whether or not the polarity nozzles should be used.

[Enable] Button: Production becomes possible, using the same

library data.

[Disable] Button: Production becomes impossible, using the same

library data.

It is required to create the library data separately

and use the data for each production.

Default: [Disable] Button Selected

(a) When the polarity nozzles are used and the same com-

ponents are arranged on both Sides A (Rear Beam)

and B (Front Beam) through component picks, the

same library data may not be used without any modi-

fication. Therefore, it is required to select this nozzle

polarity mode.

(b) Actions taken to pick up a polarity component from

the rear side

A component is picked up after the Z axis of the head

is rotated 180 degrees and it is recognized and placed

as "Component to be recognized with the movable

camera Æ Component picked up from the front side

(the head rotated back by 180 degrees after the

pickup)" or "Component to be recognized with the fixed

camera Æ Component picked up from the rear side".

*9 "Pickup level for embossed Calculation Method" Group Box

The [Ix mode] or the [TIM5000 mode (Standard)] button can be se-

lected to determine the calculation method of the embossed pickup

level.

[Ix mode] Button: The calculation method for TIM-X100 is used.

[TIM5000 mode (Standard)] Button:

The calculation method for the TIM-5000 series

is used.

Default: [Ix mode] Button Selected

There is a difference in the pickup actions (the descending

positions at component picks) for the components (Thick-

ness T

Thickness (t)) on the embossed tape between

TIM-X100 and TIM-5000 series.

Therefore, an error such as "excessive pushing" occurs

when the descending position is not specified according to

the selected data.

3.3 "OPN. Mode" Tab

0308-001 5-22-1

Note

AHB01ESPP

Pickup Level for TIM-5000 Series

Because the distance between the reference level of the em-

bossing and the pickup surface must be entered, it is required

to make the manual calculation (Principal Pickup Level + Com-

ponent Thickness (T) - Component Thickness (t)) and enter

the result of the calculation as a pickup level.

Pickup Level for TIM-X100

The distance between the reference level of embossing and

the uppermost surface of the component must be entered.

The component pickup surface (Principal Pickup Level + Com-

ponent Thickness (T) - Component Thickness (t)) is automati-

cally calculated.

*10 "Short Nozzle Mode" Group Box

"Disable" or "Enable" can be selected to determine whether or not

the short nozzles should be handled.

[Disable] Button: Only the standard nozzles can be used.

[Enable] Burron: The short nozzles can be used.

Table 2E2-1

Nozzle Types Standard Short 1 Short 2

Nozzle Length: L 19.0 13.0 11.0

Applicable Thickness 0 to 5.0 5.0 to 11.0 7.0 to 13.0

of Component

Nozzle ID E*** D*** C***

(Example: EA06) (Example: DA06) (Example: CA06)

*11 [Prev] Button

When pressed, this button opens the first page.

3.3 "OPN. Mode" Tab

0308-001 5-22-2

AHB01ESPP

3.4 "Test Run" Tab

The corresponding tab sheet enables the operator to specify a test op-

eration.

• Sheet Layout

When the "Test Run" tab is pressed in the "OPN. MODE" window

(submenu), the following tab sheet appears inside the window.

Fig. 2E14 "Test Run" Tab Sheet (Provided with Multi-Layer Tray Feeder 2)

The tab sheet may look different, depending on which options

are selected.

• Sheet Composition

*1 TEST PATTERN

When the drop-down arrow (located at the right side of the drop-

down list box) is pressed, the drop-down list opens. Select the pat-

tern to be set as a test run.

*2 Test Run

Make a combination of the following functions as a test mode.

The following buttons are provided.

[Comp. Missing Dsbl.] Button

[Vacuum Sensor Err. Dsbl.] Button

[Comp. Vertical Dsbl.] Button

[P.C.B. Location Dsbl.] Button

3.4 "Test Run" Tab

0308-004 5-23

Note