2OM-1075-002.pdf - 第182页

AHB01ESPP *7 "Operation Mode" Group Box When the [ENABLE] button on the operation panel is pressed in 2 seconds after an operation mode is selected and the [ON] button (entitled "MOVE") is pressed, th…

100%1 / 469
AHB01ESPP
*3 Indication of Coordinates
Indicated are the coordinates of the currently referred pattern pro-
gram and the teaching results.
*4 [Temp Entry] Button
When selected, this button temporarily registers the currently dis-
played coordinates for placement coordinates teaching.
*5 Recognition Window
An image captured by the recognition camera will be displayed.
*6 Contents of Pattern Program
The following items are displayed.
Total Step (#)
Displayed are the total steps in the pattern program.
[U], [P], and [O] Buttons
Displayed are the currently referred steps in the pattern program.
When each button is pressed, the selection is locked to the se-
lected step, indicating that a teaching operation can be performed
only for the step.
"X (mm)" and "Y (mm)" entitled "P-Data (Temp data)", Z (deg),
[Fdr] Button, C, S, HD, V, Component ID, and Comment
The current placement coordinates are displayed.
As for the temporarily registered data, the background color turns
blue.
When the [Fdr] button is pressed, the selection is locked to the
feeder of the selected step, making it possible to perform a teaching
operation only on the step where the feeder is specified.
[Desig Step] Button
When pressed, this button displays the arbitrarily selected steps.
0308-002 5-25-21
5.4 "Place Pos Teach" Tab
AHB01ESPP
*7 "Operation Mode" Group Box
When the [ENABLE] button on the operation panel is pressed in 2
seconds after an operation mode is selected and the [ON] button
(entitled "MOVE") is pressed, the head moves to the specified posi-
tion.
[Auto Move (High)], [Auto Move (Mid)], and [Auto Move (Low)]
Buttons
When this button is selected, the machine performs its continu-
ous operation.
Every time the button is pressed, the label on the button changes
in the order of "Auto Move (High)" Æ "Auto Move (Mid)" Æ "Auto
Move (Low)", indicating that the running speed will be changed
according to the selection.
[Step Move] Button
When this button is selected, the machine performs a step op-
eration.
*8 [TEACH] Button
When this button is selected, a teaching operation is performed at
the current position.
*9 [P.C.B. Transfer Manual Mode] Button
When this button is pressed, the "P.C.B. Transfer Manual Mode"
sheet appears.
Refer to "4.1.1 "P.C.B. Transfer Adj." Tab" in "Section 6" for details.
*10 [Cancel] Button
When pressed, this button cancels the taught data that is saved
temporarily.
*11 [End] Button
When pressed, this button saves the results (new placement coor-
dinates) of teaching and ends the teaching session.
*12 Control Button
When the [ENABLE] button on the operation panel is pressed in 2
seconds after the [ON] button (entitled "MOVE"), the machine is
activated.
When the [ON] button (entitled "STOP") is pressed, the machine
stops after a cycle of operation.
0308-002 5-25-22
5.4 "Place Pos Teach" Tab
AHB01ESPP
••
••
• Operation Procedure
(1) To find the overall shifting tendency of the P.C.B. patterns at first,
press the [ENABLE] button on the operation panel in 2 seconds
after the [Auto Move (High, Mid, or Low)] button (*7) and the [ON]
button (*12 entitled "MOVE") or after the [Step Move] button (*7) and
the [ON] button (*12 entitled "MOVE"). The X/Y beam starts moving.
(2) While the X/Y beam is moving, check the condition of the compo-
nent outline and the pattern in the recognition window.
When the patterns of a certain step are specifically shifted to one
side, it is required to teach the P-data. When the overall patterns of
a unit P.C.B. are uniformly shifted to one side, the O-data must be
taught.
(3) Move to the objective step for teaching.
The following two methods are provided for movement to the objec-
tive step for teaching.
• Move to the objective step for teaching through a continuous op-
eration and stop the movement with the [STOP] button on the
operation panel.
The speed of the automatic (continuous) operation can be
specified by selecting the [Auto Move (High)], the [Auto Move
(Mid)], or the [Auto Move (Low)] button in the "Operation
Mode" group box (*7).
• Make the objective step for teaching appear with the vertical scroll
bar in the step data area and select the step. Then, press the
[ENABLE] button on the operation panel in 2 seconds after the
[Step Move] button (*7) and the [ON] button (*12 entitled "MOVE").
(a) When the [Desig Step] button (*6) is pressed, the
desired step can be keyed in directly.
(b) The steps in the step data area are not displayed in
the order of component placement. They are dis-
played in the order of "U1, P1, O1 Æ U1, P2, O1 Æ
… Æ U1, P1, O2 Æ … Æ U2, P1, O1 Æ … Æ Un,
Pn, On".
5.4 "Place Pos Teach" Tab
0308-002 5-25-23
Note
Note