2OM-1075-002.pdf - 第418页
AHB01ESPP *3 [Feeder No.] Button and T ext Box When this button is pressed, the "Feeder No." edit window opens. Enter the feeder No. to which the head must be moved, using the ten-key pad. *4 "Selection of…
AHB01ESPP
5.14 "Nozzle Stocker Ofs" Tab
The corresponding tab sheet enables the operator to perform the teach-
ing operation on the deviation of the nozzle storage section.
The offset values are taught by automatically recognizing the pins lo-
cated on the right and left sides of the nozzle storage sections (1 through
10).
This teaching operation must be performed only by our service
personnel.
••
••
• Sheet Layout
When the "Nozzle Stocker Ofs" tab is pressed in the "TEACHING" win-
dow (submenu), the following tab sheet appears inside the window.
Fig. 2F121 "Nozzle Stocker Ofs" Tab Sheet
••
••
• Sheet Composition
*1 "Select Head" Group Box
The provided buttons make it possible to select the P.E.C. recogni-
tion camera to be used for teaching operations.
The following buttons are provided in this group box.
[X1 Head] and [X2 Head] Buttons
*2 "Nozzle Stocker Select" Group Box
Select the nozzle stocker to be used for teaching operations.
The following buttons are provided in this group box.
[Noz. Stkr. B1] and [Noz. Stkr. B2] Buttons
0206-002 6-183
5.14 "Nozzle Stocker Ofs" Tab
Note
*10
*9
*8
*11
*1
*2
*3
*5
*7
*6
*4
AHB01ESPP
*3 [Feeder No.] Button and Text Box
When this button is pressed, the "Feeder No." edit window opens.
Enter the feeder No. to which the head must be moved, using the
ten-key pad.
*4 "Selection of Teaching Operation" Group Box
The following buttons are provided in this group box.
[All Beam (Incl. NC Axis) Heads Zero] Button
When this button is pressed, all X/Y beams are zeroed.
[Teach Start] Button
When this button is pressed, the machine performs a teaching op-
eration on the selected nozzle stocker.
*5 Offset Values
Displayed are the current values and the adjusted ones after teach-
ing.
*6 Set Status
When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check
box in the "Test Run" tab sheet is turned on (checked), the back-
ground color of "Recognition Dsbl." turns light red. (No background
color in normal cases).
No recognition processing is made even if a teaching op-
eration is performed when the each check box is turned on
(checked) in the "Test Run" tab sheet. Therefore, various
teaching operations will get incorrect results.
When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-
ground color of "All Beam Zero" turns green. (Otherwise, the back-
ground has no color.)
(a) When each device is not zeroed and the teaching op-
erations are performed, note that the offset values may
not be taught correctly.
(b) Before performing a teaching operation, be sure to zero
all beams.
*7 [Noz Atch/Stor] Button
When this button is pressed, the "Nozzle Attachment/Storage Test"
sheet appears.
Refer to "5.19.1 "Nozzle Attachment/Storage Test" Sheet" for de-
tails.
*8 [Clear Adj.] Button
When pressed, this button clears the results of the teaching opera-
tion.
5.14 "Nozzle Stocker Ofs" Tab
Note
Note
0308-003 6-184
AHB01ESPP
*9 [Cancel] Button
When pressed, this button ends the teaching operation without re-
flecting the teaching results on the offset data.
*10 [End] Button
When pressed, this button reflects the results of the teaching op-
eration on the offset data and exits from this session.
*11 "Control Switch" Group Box
Select the items (buttons) to be taught and press the [ON] button
entitled "MOVE". After that, press the [ENABLE] button on the op-
eration panel in 2 seconds. A teaching operation is performed on
the selected item.
5.14 "Nozzle Stocker Ofs" Tab
0206-002 6-185