2OM-1075-002.pdf - 第68页

2 . 8 Simultaneous Pick-Up Function When two heads pick up the components from the corresponding feed- ers, both heads descend and pick up the components simultaneously , shortening the cycle time. T able 2B8 Step Refere…

2.5 Automatic Feeder Axis Adjustment Function

When a component is picked up by the nozzle and shifted from the

correct pick-up position, this function uses the recognition system to

correct the deviation for accurate component placement.

By feeding the recognized amount of correction back to the pick-up po-

sition, the pick-up position can also be brought close to the specified

one.

Table 2B5

Step Reference

1. Setting of Operation Mode "3.3 "Opn. Mode" Tab" in "Section 5"

2.6 Conveyor Width Automatic Adjustment Function

When the current program is changed, the conveyor width is automati-

cally adjusted.

Table 2B6

Step Reference

1. Program Change Operation "Section 3 Program Change Operation"

2.7 File Operation

The placement data can be saved on a 3.5-inch floppy disk in the FD

(floppy disk drive) of the front service panel or can be loaded from the

floppy disk.

• The data stored on the hard disk (HD) of the main machine can be

saved on a floppy disk (FD).

A created file can be loaded, using the network terminal (option).

• The data stored on a floppy disk (FD) can be loaded to the main

machine side.

A file of the pattern program data created on the network terminal

(option) can be loaded to the machine side. (Excl. the component

library data)

• The pattern program data on a floppy disk (FD) can be deleted.

Table 2B7

Step Reference

1. File Operation

"8. "FILE OPERATION" Window (Submenu)" in "Section

0206-002 2-18 AHB01ESPP

2.5 Automatic Feeder Axis Adjustment Function

2.8 Simultaneous Pick-Up Function

When two heads pick up the components from the corresponding feed-

ers, both heads descend and pick up the components simultaneously,

shortening the cycle time.

Table 2B8

Step Reference

1. Creating a Pattern Program

"2.5 Placement Data" in "Section 2" of "Vol. 3: Program-

ming and Machine Data"

• C02 Placement Data (P)

2.9 Pick-Up Priority Function

This function is based on the idea that the beams can be operated effi-

ciently if two heads (right and left heads) can pick up components at the

same time and follow the component placement sequence.

By pairing two steps of placement data (setting "2" in the "S" text box of

the placement data), each component can automatically be placed effi-

ciently in the order of the specified placement steps through the se-

quence "Pick Æ Pick Æ Recognition Æ Recognition Æ Place Æ Place".

The automatic feeder axis adjustment mode becomes valid for both

right and left heads when components are picked up.

Table 2B9

Step Reference

1. Creating a Pattern Program

"2.5 Placement Data" in "Section 2" of "Vol. 3: Program-

ming and Machine Data"

• C02 Placement Data (P)

01 12-002 2-19 AHB01ESPP

2.8 Simultaneous Pick-Up Function

0206-002 2-20 AHB01ESPP

2.10 Component Carriage Data Edit Function

This function enables the operator to easily change the component car-

riage data in the current pattern program.

The function can be used when the packaged posture of the supplied

component differs from that of the component being used so far due to

unavailability, etc.

Only the limited data for the packaged posture can be changed.

Table 2B10

Step Reference

1. Temporary Change of "4.2 "Comp Carriage Dt Edit" Tab" in "Section 5"

Component Carriage Data

2.11 Pick-Up Location Teaching Function

This function enables the operator to teach and correct the component

pick-up location through manual alignment operation.

After the function is performed, the pick-up rate might be improved.

Table 2B11

Step Reference

1. Pick-Up Location Teaching "5.1 "Pick-Up Location" Tab" in "Section 6"

Function

2.12 Library Teaching Function

This function enables the operator to automatically create component

library data or manually create and correct the component library data.

In addition, the recognition test function also makes it possible to make

a recognition test of the component library data.

Table 2B12

Step Reference

1. Library Teaching "5.2 Library Teaching" in "Section 6"

2.10 Component Carriage Data Edit Function

Note