2OM-1075-002.pdf - 第382页

AHB01ESPP *5 Y2 Offset Difference Shown are the values to be added to the Y-axis origin offset (Y2) for tilting correction of the beam X axis. After the teaching operation, the values must be used in the follow- ing form…

AHB01ESPP

*2 Mode Selection Buttons

Various actions can be selected.

The following button is provided in this group box.

[All Beam (Incl. NC Axis) Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, a teaching operation is performed on

the selected item.

[Chute Mark Recog.] Button

When this button is pressed, the fiducial mark on the chute is rec-

ognized to determine whether or not a teaching operation must be

performed.

When there is a big difference between the current and adjusted

values (results of chute mark recognition) in the display area of the

offset values (*4), it means that a teaching operation is required.

*3 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases)

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*4 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

Note

0206-003 6-147

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

AHB01ESPP

*5 Y2 Offset Difference

Shown are the values to be added to the Y-axis origin offset (Y2) for

tilting correction of the beam X axis.

After the teaching operation, the values must be used in the follow-

ing formula.

(X1+X2)/2

Enter the result in the "Y2 [mm]" text box in the "Y-Axis" tab sheet

that belongs to the "Offset Data" tab sheet in the "Machine System

Data - [Internal Editor]" window.

*6 [P.C.B. Transfer Manual Mode] Button

When this button is pressed, the "P.C.B. Transfer Manual Mode"

sheet appears.

Refer to "5.3.1 "P.C.B. Transfer Manual Mode" Sheet" for details.

*7 [Jig P.C.B.] Button

When this button is pressed, the "Jig P.C.B." sheet appears.

Refer to "5.3.2 "Jig P.C.B." Sheet" for details.

*8 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

*9 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*10 [End] Button

When this button is pressed, a "Confirmation" dialog box opens.

Fig. 2F106

When the [YES] button is pressed, the results of the teaching op-

eration is reflected on the offset data, and exits from this session.

*11 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

0206-003 6-148

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

AHB01ESPP

5.3.1 "P.C.B. Transfer Manual Mode" Sheet

This enables the operator to transfer and position the P.C.B.

• Sheet Layout

When the [P.C.B. Transfer Manual Mode] button is pressed in the "P.E.C.

Recog Camera & Beam Offset" tab sheet, the "P.C.B. transfer Manual

Mode" sheet appears.

Fig. 2F107 "P.C.B. Transfer Manual Mode" Sheet

• Sheet Composition

*1 "Operation" Group Box

The following buttons are provided in this group box.

[Transfer In-Cnvr Buffer Posn] Button

When this button is pressed, the P.C.B. is transferred to the

input conveyor buffering position.

[Transfer PCB Locate Posn] Button

When this button is pressed, the P.C.B. is transferred to the

positioning location and positioned there.

[Transfer P-Cnvr Buffer Posn] Button

When this button is pressed, the P.C.B. is transferred to the

positioning conveyor buffering position.

0308-004 6-149

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab