00195941-03-UM SiplaceCA-EN.pdf - 第24页
1 Introduction User Manual SIPLACE CA 1.1 Machine D escription Edition 08/2011 EN 24 1.1.5 Serial Number of the SIPLACE CA-Placement Machine 1 Fig. 1.1 - 2 Position of serial number s on the placement machines The serial…
User Manual SIPLACE CA 1 Introduction
Edition 08/2011 EN 1.1 Machine Description
23
1.1.3 SIPLACE CA4
The CA4 placement machine is equipped with four gantries, two for each placement area (PA). All
the gantry axes are driven by linear motors. The gantry axes can be positioned quickly and accu-
rately in the X and Y directions. The gantry arms are lightweight constructions made from a highly
rigid carbon fiber composite material. There is a placement head on each gantry. The following
placement head configurations are possible:
a) Placement area 1 b) Placement area 2 TH only possible with SWS 8
For the performance data refer to section 3.1, page 119.
1.1.4 SIPLACE CA3
The CA3-placement machine has 3 gantries, 2 in the placement area 1 and one in placement area
2. The following placement head configurations are possible:
a) Placement area 1 b) Placement area 2 TH only possible with SWS 8
For the performance data refer to section 3.1, page 119.
1
Placement
heads
Placement heads PA1
a
PA2
b
C&P20CA/
C&P20CA
C&P12CA/
C&P12CA
C&P12CA/
C&P6CA
C&P12CA/
TH
c
C&P6CA/
C&P6CA
C&P6CA/
TH
c
TH/TH
c
C&P20CA/
C&P20CA
yes no no no no no no
C&P12CA/
C&P12CA
yes yes no no no no no
C&P12CA/
C&P6CA
yes yes yes no no no no
C&P6CA/
C&P6CA
yes yes yes no yes no no
C&P12CA/
TH
c
yes yes yes yes no no no
Placement
heads
Placement heads PA1
a
PA2
b
C&P20CA/
C&P20CA
C&P12CA/
C&P12CA
C&P12CA/
C&P6CA
C&P12CA/
TH
c
C&P6CA/
C&P6CA
C&P6CA/
TH
c
TH
C&P20CA yes no no no no no
C&P12CA yes yes no no no no
C&P6CA yes yes yes no yes no
TH
c
yes yes yes yes yes yes
1 Introduction User Manual SIPLACE CA
1.1 Machine Description Edition 08/2011 EN
24
1.1.5 Serial Number of the SIPLACE CA-Placement Machine
1
Fig. 1.1 - 2 Position of serial numbers on the placement machines
The serial number for the SIPLACE CA placement machines can be found at two locations.
– Without prefix zeros, e.g. B-1, the serial number can be found stamped onto the side of the
pneumatic unit (1), on the left side of the machine frame.
– With prefix zeros, e.g. B-001, the serial number can be found stamped onto the type plate (2).
User Manual SIPLACE CA 1 Introduction
Edition 08/2011 EN 1.2 Description of the SIPLACE Wafer System (SWS)
25
1.2 Description of the SIPLACE Wafer System (SWS)
1.2.1 Description and Principle of Function
Up to four SIPLACE Wafer Systems (SWS) can be used at the SIPLACE CA placement machines.
The SWS provides the placement head with components directly from the wafer. The SWS there-
fore extends the component spectrum of the established SIPLACE X machines, by enabling
placement of bare dies from wafers.
The wafers are automatically supplied from the wafer magazine and the components can be pro-
cessed in the known placement methods.
Flip chip process - function
The wafer is automatically transported from the wafer magazine on the wafer table. This then po-
sitions the die concerned over the ejection system, which releases the die from the wafer foil. After
this release procedure, the flip unit nozzle takes the die, rotates it by 180° and makes it available
to the placement head for pickup.
The process spectrum is supplemented by the following options:
– Die attach unit:
The die attach unit takes the die from the flip unit nozzle and turns it, so that it has the same
top-bottom orientation on the board as it had on the wafer.
– Linear Dipping Unit
The Linear Dipping Unit distributes precise layers of flux for the flip chip process. After taking
over from the flip unit the placement head dips the die in to the flux layer.