00195941-03-UM SiplaceCA-EN.pdf - 第362页

5 Tasks on the Mach ine User Manual SIPLACE CA 5.7 LCD and Status Display at the X-Feeder Mod ule Edition 08/2011 EN 362 5 NOTE 5 Remove th e compone nt tape before a referenc e run. Referenc e o Referenc e o Red Positio…

User Manual SIPLACE CA 5 Tasks on the Machine

Edition 08/2011 EN 5.7 LCD and Status Display at the X-Feeder Module

361

Handle --->>

(Handle --->>)

Red Feeder module was sig-

naled, but removal handle is

not yet pushed in

Push in the removal handle

Low Voltage

(Low voltage)

Orange 24V supply voltage did not

rise above the switch-on

threshold after switching on

Check the power supply

Low Voltage

(Low voltage)

Red 24V supply voltage rose

above the switch-on thresh-

old after switching on and

was then interrupted

Check the power supply

Feed Time-out

TransTimeout

(Transfer time-out

error during tape

transfer cycle)

Red Tape feeder cycle did not

end correctly within the spec-

ified time (time-out for the

"Feed" function)

Is the tape reel jammed in the container?

Is there a component jammed in the pickup

area between component tape and compo-

nent window?

Once the obstacle has been eliminated, use

the arrow keys to restart the conveyor. The

feeder module will move the defective con-

veyor to the end, and then returned to its

position

Foil Torn

(foil torn)

Red Foil was not tensioned within

the specified time

The foil is probably torn. Insert new foil and

tension

Foil PeelErr

(Error while peel-

ing off the foil)

Red Foil was not peeled off even

though the tape is moved

The cover foil is probably jammed beneath

the pickup window and cannot be peeled off

correctly

Foil Jam

(foil jam)

Red Foil motor has locked up Leveling gears blocked by foil? => Remove

the foil

EEP-WriteErr

(Error while back-

ing up data in the

EEPROM)

Red The data back-up in the EE-

PROM was not carried out

correctly

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pickup window).

Press the SET button to confirm the error.

Then press the yellow button to confirm the

reference run prompt.

EEP-ReadErr

(Error reading out

EEPROM)

Red Data was not read from the

EEPROM correctly

EEP-DataErr

(Error while back-

ing up the data in

the EEPROM)

Red The data back-up in the EE-

PROM was not carried out

fully

Text on the

LCD display

Status

display

Meaning Troubleshooting

5 Tasks on the Machine User Manual SIPLACE CA

5.7 LCD and Status Display at the X-Feeder Module Edition 08/2011 EN

362

NOTE 5

Remove the component tape before a reference run.

Reference o

Red Position information is no

longer available for the com-

ponent tape drive

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pickup window).

Then press the "FOIL" button to start the

reference run.

CAN BusError

(CAN Bus error)

Red CAN bus error Log off and on again, check the optical fiber

interface

ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-

ly, i.e. the most recent operator settings are

overwritten -> The settings (e.g. increment)

will have to be made again. Replace the

control board if this error occurs frequently.

ParWrongSave Red Wrong or incomplete param-

eters were saved

BootFlashErr

FlashDataErr

Red Can no longer write to boot

or application memory cor-

rectly

Replace the feeder module or control board

Text on the

LCD display

Status

display

Meaning Troubleshooting

User Manual SIPLACE CA 5 Tasks on the Machine

Edition 08/2011 EN 5.8 Changing Setups

363

5.8 Changing Setups

5.8.1 Changing Setups at the Placement Machine

5.8.1.1 Printing Setup Changeover Instructions Before Setup Changes

Before a change of setup, print out the conversion instructions on the printer for the SIPLACE Pro

computer as described in the "SIPLACE Pro" manual or in the online help.

5.8.1.2 What You Should Note when Changing the Feeder Modules

 Handle the feeder modules carefully when you insert them into or remove them from the com-

ponent feeder table. Do not hit the X feeder against the centering bar (see item 5 in fig. 5.5 -

3, page 353) of the changeover table.

 Vacuum the supporting surfaces of the feeder modules and clean the surface of the compo-

nent feeder table when necessary according to the instructions in the Preventive Mainte-

nance Manual.

 Remove loose components using a brush or a vacuum cleaner with a suitable nozzle.

CAUTION 5

Avoid removing components from the component table with your fingers. You may hurt your-

self with tiny splinters of metal.