00195941-03-UM SiplaceCA-EN.pdf - 第352页
5 Tasks on the Mach ine User Manual SIPLACE CA 5.5 Configuring Feeders Edition 08/2011 EN 352 NOTE 5 Do not press the lever if a componen t tape is inserted . The tensioned cover foil would move the component t a pe on a…
User Manual SIPLACE CA 5 Tasks on the Machine
Edition 08/2011 EN 5.5 Configuring Feeders
351
When ready for operation, the status display (item 2 in fig. 5.5 - 1) shines green, provided the X
feeder is contained in the current setup. If the feeder module is not contained in the current setup,
the status display remains off.
The X feeder module is locked in position in the component table by a latch, and cannot be pulled
out. The procedure for removing feeder modules from the component table is as follows:
Press the removal handle (item 1 in fig. 5.5 - 1). The removal handle jumps out and the
status display goes out.
Wait roughly 1 second, until the lock (item 4 in fig. 5.5 - 1) releases the feeder.
Use the removal handle to pull the feeder module out of the component table. If you wait
longer than 5 seconds, the feeder module will be locked once more. The status display
will shine red and the LCD display (item 3 in fig. 5.5 - 1
) will show the message "Handle
--->>".
Engage the removal handle once more. If the X feeder module is contained in the current
setup, the status display lights up green and the track number and increment are appear
on the LCD display once more.
Press the removal handle again (item 1 in fig. 5.5 - 1) and pull the feeder out of the
changeover table.
5.5.3 Using the X Feeder Module on the Component Trolley (X Series)
5.5.3.1 Checking X-Feeder Module before Insertion
Check the following points before you use a feeder module on the component table:
The feeder module must be in perfect condition.
Gently tap the feeder, to make sure that the cover foil rocker (item 2 in fig. 5.5 - 2) does
not jam.
Check whether the pickup window area (item 3 in fig. 5.5 - 2) is free of loose components.
NOTE 5
Empty the component reject compartment (item 5 in fig.5.5 - 2
), before you shake the com-
ponents out of the feeder.
Press the lever (item 4 in fig. 5.5 - 2) to open the pickup window (item 3 in fig. 5.5 - 2) a
little, towards the front. This will raise the pickup window slightly.
5 Tasks on the Machine User Manual SIPLACE CA
5.5 Configuring Feeders Edition 08/2011 EN
352
NOTE 5
Do not press the lever if a component tape is inserted. The tensioned cover foil would move
the component tape on and expose the components.
Remove any loose components from beneath the pickup window.
Close the pickup window (item 3) by returning the lever (item 4) to its original position.
Remove loose components from the component feeder table with a brush or use a vac-
uum cleaner with appropriate nozzle.
NOTE 5
If the component tape is already inserted, cut it off flush with the front edge of the feeder mod-
ule.
If the removal handle (item 1) is still protruding, then latch it in place.
5
Fig. 5.5 - 2 Checking X-feeder module before insertionn
(1) Removal handle (2) Cover foil rocker
(3) Pickup window (4) Lever for raising and latching the pickup
window
(5) Component reject compartment
User Manual SIPLACE CA 5 Tasks on the Machine
Edition 08/2011 EN 5.5 Configuring Feeders
353
5.5.3.2 Using the X Feeder Module on the Component Table
5
Fig. 5.5 - 3 Using the X feeder module on the component table
(1) Front slider guide for the X feeder module
(2) Back slider guide for the X feeder module
(3) "Back" centering pin on the X feeder module
(4) "Front" centering pin on the X feeder module
(5) Recesses in the centering bar for holding the "back" centering pin
(6) Centering holes at the component table for receiving the front centering pin
(7) Locking latches
(8) Guide profile for the component table ( profile)
(9) Insertion aid for the feeder module
5
Place the front slider guide (item 1) of the feeder module on the insertion aid (item 9) for the
component table.
Hold the feeder module vertically and push it forward, along the guide profile (item 8). The
front (item 1) and rear (item 2) slider guides of the feeder module slide on the guide profile
(item 8).
Carefully push the feeder module further until the "front" centering pin (item 4) is pushed into
the centering hole (item 6).