00195941-03-UM SiplaceCA-EN.pdf - 第293页
User Manual SIPLACE CA 4 Setting Up and Commissioning Edition 08/2011 EN 4.5 Setting Up the Placement Machine 293 4.5.10 Inst all Extension Ki t on the PCB Input Side 4.5.10.1 T ools – Allen keys, DIN 91 1, set – Machine…
4 Setting Up and Commissioning User Manual SIPLACE CA
4.5 Setting Up the Placement Machine Edition 08/2011 EN
292
Dismantle the cable covers (item 3 and 5 in fig. 4.5 - 14) of the input conveyor (item 1 in fig.
4.5 - 14
).
Place the side (item 1 in fig. 4.5 - 14) carefully on the side of the processing conveyor (item
2 in fig. 4.5 - 14
).
CAUTION 4
Be careful not to cut through any of the light barrier or drive motor cables.
Fasten each side with 4 fillister head screws M6x16 and the corresponding discs (item 7 in
fig. 4.5 - 14
).
Connect the power cable to the light barriers and drive motors.
Fasten the cable covers (item 3 and 5 in fig. 4.5 - 14).
Insert the hexagonal shaft (item 9 in fig. 4.5 - 14) into the drive unit (item 10 in fig. 4.5 - 14).
Make sure that the hexagonal shaft guidance (item 8 in fig. 4.5 - 14) is always pointing to-
wards the conveyor side on which the drive unit (item 10 in fig. 4.5 - 14
) is fixed.
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.5 Setting Up the Placement Machine
293
4.5.10 Install Extension Kit on the PCB Input Side
4.5.10.1 Tools
– Allen keys, DIN 911, set
– Machine key
4.5.10.2 Setting Up
4
Fig. 4.5 - 15 Install extension kit on the PCB input side
(1) Extension kit, dismantled
(2) Door
(3) Fillister head screw DIN 912, M6x16 and washer
(4) Grounding connection
(5) Transport cover
(6) Side plate, dismantled
(7) Insert rail
(8) Computer unit or Box PC unit (see section 4.5.11
, page 298)
(9) Axis slide in (CA4CA3)
4 Setting Up and Commissioning User Manual SIPLACE CA
4.5 Setting Up the Placement Machine Edition 08/2011 EN
294
Remove both side plates (item 6 in fig. 4.5 - 15).
CAUTION 4
Do not unscrew the three bottom screws straight away. Simply loosen them so that the side
plate does not fall off.
Detach the ground cable from the side plate.
Remove both doors (item 2 in fig. 4.5 - 15) from the extension kit (item 1).
Note: 4
To avoid damage, we recommend that a second person helps to assemble the extension kit.
Place the computer unit/Box PC unit
a
(item 8 in fig. 4.5 - 15) and the axis unit (item 9 in fig.
4.5 - 15
) down at the side of the placement machine, so that you have enough room to fit the
extension kit (item 1 in fig. 4.5 - 15
).
Make sure that the connection cable to the computer unit / Box PC unit and the axis unit is
not under tension.
Lift one half of the extension kit (item 1 in fig. 4.5 - 15) up to the machine frame and position
it so that the mounting bracket lies on the assembly insert rail (item 7 in fig. 4.5 - 15
).
CAUTION 4
Make sure that the extension kit does not collide with the hexagonal shaft of the PCB con-
veyor and thus become bent.
Fasten this half of the extension kit with 2 fillister head screws M6x16 and the corresponding
discs (item 3 in fig. 4.5 - 15
).
Before assembling the second half of the extension kit, fit the conveyor covers (item 5 in fig.
4.5 - 15
). The procedure is as follows:
a)