00195941-03-UM SiplaceCA-EN.pdf - 第328页
4 Setting Up and Commissioning User Manual SIPLACE CA 4.7 Adapting the SIPLACE X-Series Component Trol ley to the PCB Conveyor Heig ht Edition 08/2011 EN 328 4.7 Adapting the SIPLACE X-Series Component T rol- ley to the …
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.6 Installing the SWS
327
4.6.4 Removing the Transportation Locks
– Remove all transport locks:
– Flip rotary axis
– Wafer table (X/Y axis)
– Wafer changer feed axis (if present)
4.6.5 Removing the Corrosion Protection from the Guide Rails
Check whether the SWS has been treated with corrosion protection agent. This must be removed
before setting up the SWS.
CAUTION 4
– You should therefore remove the corrosion protection from all the axes and bearings when
you traverse the machine axes for the first time during commissioning.
– Grease all the axes and bearings with the grease described in the maintenance instructions.
If the corrosion protection agent is mixed with the bearing grease on the axes this can greatly re-
duce the service life of the bearings and guide rails.
CAUTION 4
Do not allow any alcohol to enter the guide carriages when you clean the guide rails and scale
rods. Alcohol will damage the bearing grease in the guide carriages.
4.6.6 Power Supply
After performing final adjustment, connect the SWS to the power supply.
4 Setting Up and Commissioning User Manual SIPLACE CA
4.7 Adapting the SIPLACE X-Series Component Trolley to the PCB Conveyor Height Edition 08/2011 EN
328
4.7 Adapting the SIPLACE X-Series Component Trol-
ley to the PCB Conveyor Height
The component trolley for the X feeder modules can be set to the following PCB conveyor heights
with just a few simple actions:
830 mm ± 15 mm (standard height), 900 mm ± 15 mm, 930 mm ± 15 mm,
950 mm ± 15 mm (SMEMA height) 4
4
Fig. 4.7 - 1 Component trolley (SIPLACE X-series) with a PCB conveyor height of 950 mm
(1) Holes in the guide columns for the conveyor heights of 900, 930 and 950 mm.
If the conveyor height is 830 mm, the component table lies on the block (2).
(2) Block
(3) Component table
(4) M8 holes for fixing the assembly guide
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.7 Adapting the SIPLACE X-Series Component Trolley to the PCB Conveyor Height
329
4.7.1 Warning Instructions
WARNING 4
Only technicians of the company ASM Assembly Systems GmbH & Co.KG or other certified per-
sonel may change the height of the component table.
Always follow the applicable accident prevention regulations.
Remove all the feeder modules from the component table, if you want to adjust the height for
the component feeder table.
4.7.2 Tools and Equipment
You will need the following tools and equipment to adjust the height of the component trolley:
– Hammer
–Punch, 8 mm
– Assembly guide [03015976-xx]
– Lifting device for raising the component trolley table, carrying capacity at least 80 kg
4.7.3 Changing the Component Trolley Height
WARNING 4
Remove all the feeder modules from the component table.
Fit the assembly guide to the component table in order to adjust the height. This prevents the
component table becoming deformed when the table is raised or lowered.
Fasten the assembly guide (item 1 in fig. 4.7 - 2) with the two hexagon socket-head screws
M8 x 50 (item 3 in fig. 4.7 - 2
) to the changeover table (item 4 in fig. 4.7 - 2).
Hook the lifting device into the eyelet (item 2 in fig. 4.7 - 2).
Lift the component trolley table slightly, until the split pins (item 6 in fig. 4.7 - 2) are accessible.
Use the punch to carefully tap out the split pins on both sides.
Insert the split pins into the drillings for the required PCB conveyor height (see fig. 4.7 - 1).
Slowly lower the component trolley table, until the split pins lie on the supporting blocks (item
5 in fig. 4.7 - 2
).
Dismantle the assembly guide