00195941-03-UM SiplaceCA-EN.pdf - 第329页
User Manual SIPLACE CA 4 Setting Up and Commissioning Edition 08/2011 EN 4.7 Adapting the SIPLACE X-Series Component Tr olley to the PCB Conveyor Height 329 4.7.1 W arning Instructions WA R N I N G 4 Only techni cians of…
4 Setting Up and Commissioning User Manual SIPLACE CA
4.7 Adapting the SIPLACE X-Series Component Trolley to the PCB Conveyor Height Edition 08/2011 EN
328
4.7 Adapting the SIPLACE X-Series Component Trol-
ley to the PCB Conveyor Height
The component trolley for the X feeder modules can be set to the following PCB conveyor heights
with just a few simple actions:
830 mm ± 15 mm (standard height), 900 mm ± 15 mm, 930 mm ± 15 mm,
950 mm ± 15 mm (SMEMA height) 4
4
Fig. 4.7 - 1 Component trolley (SIPLACE X-series) with a PCB conveyor height of 950 mm
(1) Holes in the guide columns for the conveyor heights of 900, 930 and 950 mm.
If the conveyor height is 830 mm, the component table lies on the block (2).
(2) Block
(3) Component table
(4) M8 holes for fixing the assembly guide
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.7 Adapting the SIPLACE X-Series Component Trolley to the PCB Conveyor Height
329
4.7.1 Warning Instructions
WARNING 4
Only technicians of the company ASM Assembly Systems GmbH & Co.KG or other certified per-
sonel may change the height of the component table.
Always follow the applicable accident prevention regulations.
Remove all the feeder modules from the component table, if you want to adjust the height for
the component feeder table.
4.7.2 Tools and Equipment
You will need the following tools and equipment to adjust the height of the component trolley:
– Hammer
–Punch, 8 mm
– Assembly guide [03015976-xx]
– Lifting device for raising the component trolley table, carrying capacity at least 80 kg
4.7.3 Changing the Component Trolley Height
WARNING 4
Remove all the feeder modules from the component table.
Fit the assembly guide to the component table in order to adjust the height. This prevents the
component table becoming deformed when the table is raised or lowered.
Fasten the assembly guide (item 1 in fig. 4.7 - 2) with the two hexagon socket-head screws
M8 x 50 (item 3 in fig. 4.7 - 2
) to the changeover table (item 4 in fig. 4.7 - 2).
Hook the lifting device into the eyelet (item 2 in fig. 4.7 - 2).
Lift the component trolley table slightly, until the split pins (item 6 in fig. 4.7 - 2) are accessible.
Use the punch to carefully tap out the split pins on both sides.
Insert the split pins into the drillings for the required PCB conveyor height (see fig. 4.7 - 1).
Slowly lower the component trolley table, until the split pins lie on the supporting blocks (item
5 in fig. 4.7 - 2
).
Dismantle the assembly guide
4 Setting Up and Commissioning User Manual SIPLACE CA
4.7 Adapting the SIPLACE X-Series Component Trolley to the PCB Conveyor Height Edition 08/2011 EN
330
4
Fig. 4.7 - 2 fastening the assembly guide to the changeover table of the SIPLACE component trolley
(1) Mounting aid
(2) Eyelet
(3) Hexagon socket head screw DIN 912, M8 x 50, 2 x
(4) M8 threaded hole in the component table, 2x
(5) Supporting block, 2x
(6) Split pin, DIN 7343, 8 x 40 - St, 2 x