00195941-03-UM SiplaceCA-EN.pdf - 第361页

User Manual SIPLACE CA 5 Tasks on the Machine Edition 08/2011 EN 5.7 LCD and Status Display at the X- Feeder Module 361 Handle --->> (Handle --->>) Red Feeder module was sig- naled, but removal ha ndle is not…

5 Tasks on the Machine User Manual SIPLACE CA

5.7 LCD and Status Display at the X-Feeder Module Edition 08/2011 EN

360

Fig. 5.7 - 1 Buttons, LCD and status displays on the X feeder module

The following tables show the wording of the LCD display, the color and the mode of the status

display, the description of the errors and measures for troubleshooting.

5.7.1 Warnings

5.7.2 Error Messages and Troubleshooting

(1) LCD display (2) FORWARD button

(3) BACK button (4) FOIL button

(5) SET button (6) Status display, multicolor

Text on the

LCD display

Status

display

Meaning Troubleshooting

Remove Foil

(Remove the foil)

Orange The selected function is not

permitted when the cover foil

is tensioned (foil rocker is

pressed down).

If you wish to carry out that function, remove

the foil from the pair of gear wheels and cut

it off to relieve the pressure on the foil rocker.

Text on the

LCD display

Status

display

Meaning Troubleshooting

none Red,

flashing

Feeder module software not

jumping to the application

Reload the application software

Load feeder module software

User Manual SIPLACE CA 5 Tasks on the Machine

Edition 08/2011 EN 5.7 LCD and Status Display at the X-Feeder Module

361

Handle --->>

(Handle --->>)

Red Feeder module was sig-

naled, but removal handle is

not yet pushed in

Push in the removal handle

Low Voltage

(Low voltage)

Orange 24V supply voltage did not

rise above the switch-on

threshold after switching on

Check the power supply

Low Voltage

(Low voltage)

Red 24V supply voltage rose

above the switch-on thresh-

old after switching on and

was then interrupted

Check the power supply

Feed Time-out

TransTimeout

(Transfer time-out

error during tape

transfer cycle)

Red Tape feeder cycle did not

end correctly within the spec-

ified time (time-out for the

"Feed" function)

Is the tape reel jammed in the container?

Is there a component jammed in the pickup

area between component tape and compo-

nent window?

Once the obstacle has been eliminated, use

the arrow keys to restart the conveyor. The

feeder module will move the defective con-

veyor to the end, and then returned to its

position

Foil Torn

(foil torn)

Red Foil was not tensioned within

the specified time

The foil is probably torn. Insert new foil and

tension

Foil PeelErr

(Error while peel-

ing off the foil)

Red Foil was not peeled off even

though the tape is moved

The cover foil is probably jammed beneath

the pickup window and cannot be peeled off

correctly

Foil Jam

(foil jam)

Red Foil motor has locked up Leveling gears blocked by foil? => Remove

the foil

EEP-WriteErr

(Error while back-

ing up data in the

EEPROM)

Red The data back-up in the EE-

PROM was not carried out

correctly

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pickup window).

Press the SET button to confirm the error.

Then press the yellow button to confirm the

reference run prompt.

EEP-ReadErr

(Error reading out

EEPROM)

Red Data was not read from the

EEPROM correctly

EEP-DataErr

(Error while back-

ing up the data in

the EEPROM)

Red The data back-up in the EE-

PROM was not carried out

fully

Text on the

LCD display

Status

display

Meaning Troubleshooting

5 Tasks on the Machine User Manual SIPLACE CA

5.7 LCD and Status Display at the X-Feeder Module Edition 08/2011 EN

362

NOTE 5

Remove the component tape before a reference run.

Reference o

Red Position information is no

longer available for the com-

ponent tape drive

Remove the component tape (tape can be

moved out by pressing the arrow keys or

pulled out after raising the pickup window).

Then press the "FOIL" button to start the

reference run.

CAN BusError

(CAN Bus error)

Red CAN bus error Log off and on again, check the optical fiber

interface

ParNotSaved! Red Parameters were not saved Default parameters are loaded automatical-

ly, i.e. the most recent operator settings are

overwritten -> The settings (e.g. increment)

will have to be made again. Replace the

control board if this error occurs frequently.

ParWrongSave Red Wrong or incomplete param-

eters were saved

BootFlashErr

FlashDataErr

Red Can no longer write to boot

or application memory cor-

rectly

Replace the feeder module or control board

Text on the

LCD display

Status

display

Meaning Troubleshooting