JUKI贴片机错误代码.pdf - 第102页
again .” “ 机器发 生异常，请退出生产，关闭系统 后，重新启动。 ” E500500 “ Teaching can not be executed ” “ 不能执行示教。 ” [Cause] You are trying to teach unexecu ted data to the machine. Unexecuted data: Data except ref. circuit in th e Placement po…
“发现%s 上传送带浮动。”
[Cause]
A matter that may interrupt the Feeder floatation sensor occurred.
where the matter occurred.
‧On the front side
‧On the rear side
‧On both sides
[Treatment]
Please remove the obstruction that may be interrupting the sensor.
E500304 “The servo power supply does not enter for the cover opening. |Please close the cover.”
“因机盖被打开，不能启动起动伺服。|请关闭机盖。”
E500305 “The servo power supply does not enter for the bank descent. |Please raise the bank.”
“因送料器台架被下降，不能启动伺服。|请台升送料器台架。”
E500400 “Machine was gone to abnormal state”
“机器有些不正常。”
E500401 “Input order Simple Opt. Error <%s>“ “建立进度表数据出错 |<%s>“
[Cause]
An error occurred while optimizing the pick positions by input orders.
The details of the error
1. There is no component corresponding to the feeder.
2. The head can not travel to the feeder/MTC position.
3. The head can not travel to the holder/MTS position.
4. There is no head available to place the component.
5. There is no head that meets the centering type.
6. An internal error of the Input order Simple Opt. Error process.
[Treatment]
1 and 6 are a program error. Please make a note of the cause of the error and the error code, then
contact our technical service Dept. for information.
In case of 2, 3, and 4, please go to the Production Program Editor and see the specified head(s) in the
Placement data.
In case of 5, please go to the Production Program Editor and see the centering type in the Component
data.
E500402 “An error occurred in the checking prior to the production. |<%s>“
“在生产开始之前的检测中发生错误。|<%s>“
E500403 “Machine was gone to abnormal state.|The process gets discontinued. |Please put the power supply
again.”
“机器发生异常，请退出生产，关闭系统后，重新启动。”
E500500 “Teaching can not be executed”
“不能执行示教。”
[Cause]
You are trying to teach unexecuted data to the machine.
Unexecuted data:
Data except ref. circuit in the Placement position teaching.
Components except tray component in the Pick position teaching.
When multiple heads are working at the same time.
[Treatment]
You can not perform a teaching with the current status. Please go on the process.
E500501 “The selected device can not be used”
“不能使用被选设备。”
[Cause]
You selected a device not available.
[Treatment]
Please change devices to use.
E500502 “With the selected device, it is impossible to move to the aimed position”
“被选设备不能移到目的位置。”
[Cause]
You can not move to the specified position with the selected device.
[Treatment]
Please select another device.
E500503 “Standard Pin position illegal. Correct coordinates can not acquire”
“基准针位置不对。|不能取得正确坐标。”
[Cause]
The position of the reference pin is not correct.
[Treatment]
In the Setup, please teach the positions of the reference pin and follower pin to the machine.
E500600 “YC table error. Code : %d”
“Yc 支撑台出错。|代码 : %d”
E500601 “Axis movement error. Code : %d”
“轴通讯错误”
E500602 “An error occurred while performing Yc table end check. Code : %d”
“结束 Yc 支撑台检查时，发生错误。|代码 : %d”
E500603 “An error occurred while performing axis end check. Code : %d”
“结束轴移动检查时，发生错误。|代码 : %d”
E500605 “An error occurred when disposing a component”
“废弃组件发生错误。”
[Cause]
This error occurs if the component present check at a component disposal action gets an error when
starting a production.
[Treatment]
Pressing OK button will abort the process. In this case, the production will not be executed.
E500700 “An error occurred while Auto. PWB Width Alignment Control. | The process gets discontinued”
“自动调整基板宽度发生错误。|退出操作。”
[Cause]
This error occurs if an error occurs or an action did not take place properly while Auto. PWB Width
Alignment Control.
[Treatment]
Pressing OK button will abort the process. If a particular reason (Home returning has not been
complete, etc.) why Auto. PWB Width Alignment Control can not be executed is given, please
perform any means to get rid of the factor that stops Auto. PWB Width Alignment Control. If any
particular reasons are not given, please, check the action of Auto. PWB Width Alignment Control by
Manual control .
E500701 “Para error. PWB Width Alignment Control occurred”
“自动调整基板宽度参数错误”
[Cause]
This error occurred if an entered value to be defined by Enter key is wrong when performing Auto.
PWB Width Alignment Control.
[Treatment]
Please check the entered value.
E500710 “An error occurred while Auto. BOC mark.|The process gets discontinued.”
“识别 BOC 标记发生错误|退出操作。”
E500711 “Param error|BOC mark occurred.”
“识别 BOC 标记参数错误”
E500800 “A PWB is detected within the conveyors of both stations. Please remove the PWB”
“两个站台内的传送轨道上，发现基板。|请取下基板。”