JUKI贴片机错误代码.pdf - 第119页
cannot be executed .” “ 吸取位置或使用单元的设置不整合 ， | 不能进行输入顺生产。 ” W503860 “ Order production warning.|Resum e the product cannot be execut ed .” “ 这次生产条件与继续生产程序条件 不同。 | 不能进行继续生产。 ” W503900 “ There is a possibility with whic h the…
“在设置数据中，传送带浮动选项为无效状态，|不间断运行被选用。”
W503600 “The input data is over the Input range(%s).|Would you like to set the data?”
“输入的数据超过输入范围，|是否继续设置？”
W503601 “The input data is changed.|Is the data setting ended?”
“数据正在被更新，|是否结束数据更新？”
W503700 “There is no Data.|Please select the area where the data is displayed.”
“没有数据，|请选择数据。”
W503800 “The head is specified for an unused head by the place data.|The input order production cannot be
executed.”
“在贴片数据上，指定了不使用 Head，|不能进行输入顺生产。”
W503801 “Right or Left OCC is unused.|(There is both head specification in the production program.)|The
input order production cannot be executed.”
“不使用或左或右 OCC|(生产程序内已经指定两个 Head)，|不能进行输入顺生产。”
W503802 “Left OCC is unused.|(There is left head specification in the production program.)|The input order
production cannot be executed.”
“不使用左 OCC|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503803 “Right OCC is unused.|(There is right head specification in the production program.)|The input order
production cannot be executed.”
“不使用左 OCC|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503804 “There is a station which it is a setup and is unused.|(There is both head specification in the
production program.)|The input order production cannot be executed.”
“在设置中存在不使用站台|(生产程序内已经指定两个 Head)，|不能进行输入顺生产。”
W503805 “It is a setup and a left station is unused.|(There is left head specification in the production
program.)|The input order production cannot be executed.”
“在设置中，左站台处于不使用状态|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503806 “It is a setup and a right station is unused.|(There is right head specification in the production
program.)|The input order production cannot be executed.”
“在设置中，右站台处于不使用状态|(生产程序内已经指定右 Head)，|不能进行输入顺生产。”
W503810 “It is the data which the exit side station installs earlier than the entrance side station.|The input
order production cannot be executed.”
“存在出口侧站台比入口侧站台先进行贴片的数据，|不能进行输入顺生产。”
W503820 “There is no adjustment in setting the pick position and the use unit.|The input order production
cannot be executed.”
“吸取位置或使用单元的设置不整合，|不能进行输入顺生产。”
W503860 “Order production warning.|Resume the product cannot be executed.”
“这次生产条件与继续生产程序条件不同。|不能进行继续生产。”
W503900 “There is a possibility with which the laser of %s is dirty. Is production executed?”
“%s 的激光可能被弄脏，是否进行生产？”
W503910 “Nozzle is set on %s.|Remove the nozzle.|Nozzle moves to nozzle of wait position by selecting
'OK'.”
“%s 位置上吸嘴被安装，|请取出吸嘴，|选择确定键，移到模具位置。”
W504000 “The PWB on LEFT station can't re-clamp.”
“在左站台上，不能重新固定基板。”
W504001 “The PWB on RIGHT station can't re-clamp.”
“在右站台上，不能重新固定基板。”
W504002 “Remove the PWB on LEFT station.”
“请取下左站台上的基板。”
W504003 “Remove the PWB on RIGHT station.”
“请取下右站台上的基板。”
W504004 “The PWB on LEFT station don't exist.”
“左站台的传送轨道上无基板。”
W504005 “The PWB on RIGHT station don't exist.”
“右站台的传送轨道上无基板。”
W504006 “The PWB on BOTH station can't re-clamp.”
“在两个站台上，都不能重新固定基板。”
W504007 “Remove the PWB on BOTH station.”
“请取下两个站台上的基板。”
W504008 “The PWB on BOTH station don't exist.”
“两个站台的传送轨道上都没有基板。”
W504009 “The PWB on the station can't re-clamp.”
“不能重新固定基板。”
W504010 “Remove the PWB on the station.”
“请取下基板。”
W504011 “The PWB on the station don't exist.”
“传送轨道上没有基板。”
W504012 “When sequential mode or mixed mode,the PWB on %s can't re-clamp.”
“次序混合模式生产时，不能运行%s 的重新固定基板。”
W504020 “When left station is specified,the PWB on RIGHT station can't re-clamp.”
“指定左站台时，如果右站台上存在基板，就不能重新固定。”
W504021 “When left station is specified,the PWB on LEFT station can't re-clamp.”
“指定右站台时，如果左站台上存在基板，就不能重新固定。”
W507603 “You can use this program for measuring general placement offset.”
“贴片综合偏差生产用生产程序。”
Q506001 “The measurement of the height of component of the %s failed.|Do you measure again?”
“测量%s 送料器组件高度失败，|是否再试？”
Q506002 “Stop Key is pressed in the measurement of the height of component of the %s.|Do you want to exit
measurement?”
“测量%s 送料器组件高度，被停止按钮而停止，|是否停止测量？”
Q506011 “Verification inspection of component of the %s failed.| Specified value| %s|
Measurement value| %s| Inspection result| %s|Do you inspect again?”
“测量%s 送料器组件的数值检查失败。| 指定值: %s | 测定值：%s | 检查结果: %s | 是否再
检查？ “。
Q506012 “Stop Key is pressed in verification inspection of component of the %s.|Do you want to exit
inspection?”
“测量%s 送料器数值检查中停止健被按下，|是否结束检查？ “
Q506021 “SOT direction inspection of component of the %s failed.|Do you inspect again?”
“%s 送料器组件 SOT 方向检查失败，|是否再试？”
Q506022 “Stop Key is pressed in SOT direction inspection of component of the %s.|Do you want to exit
inspection?”
“%s 送料器组件 SOT 方向检查，被停止按钮而停止，|是否停止检查？”
E506100 “You can resume the production from the last suspended position |%s |%s | Would you like to
resume the production?”
[Cause]
This message appears if the production is resumable when reading a file in.
|Resumptive production starting position of each station.