JUKI贴片机错误代码.pdf - 第153页
“ 激光错误 :(NO_ALG) | 被要求错误测量方法。 ” E521008 “ Laser Error:(NO_START) | Eiter the sensor is not connect ed or t here is a ha rdware error .” “ 激光错误 :(NO_START) | 没有连接传感器，或硬件 出错。 ” E521010 “ Laser Error:(BAD_SENSOR) | The MCM …
Q514601”May I abandon MTS parts?”
“是否废弃 MTS 组件？”
I514802 “It is temporary stop by the part protection.|Please detach parts.”
“为保护组件暂停。|请取下组件。”
E515001 “DTS abnormal operation was generated.”
“DTS 运转异常。”
E515002 “Parts that DTS is different were drawn out.”
“DTS 抽出不同组件。”
W515401”DTS is an initialize.”
“DTS 未结束原点返回。”
W515402”DTS is a cover opening.”
“DTS 机盖被打开。”
W515403”DTS is making an error.”
“DTS 处于出错状态。”
W515404”DTS is exchanging parts.”
“DTS 处于交换组件状态。”
E520000 “Pick Miss Occured from MTC shuttle”
“不能吸取 MTC 上的组件。”
E520001 “The componet On MTC shuttle is different with Requested one”
“MTC 上的组件与指定组件不一致。”
E520002 “MTC Error Occured when doing Componet return to MTC”
“给 MTC 归还组件时，MTC 发生错误。”
E520003 “MTC shuttle Vacuum Error Occured when doing Componet return to MTC”
“给 MTC 滑梭归还组件时，滑梭真空出错。”
E520012 “When a component was returned to MTC shuttle,| the error of bringing a component to the head
occurred.”
“给 MTC 滑梭归还组件时，|发生 Head 附着组件返回的错误。”
E521005 “Laser Error:(LNK_FAIL) | A data error occurred on the communication link from the sensor to the
MCM.”
“激光错误:(LNK_FAIL) |传感器与 MCM 之间通讯发生错误。”
E521007 “Laser Error:(NO_ALG) | The NO_ALG action was requested.”
“激光错误:(NO_ALG) |被要求错误测量方法。”
E521008 “Laser Error:(NO_START) | Eiter the sensor is not connected or there is a hardware error.”
“激光错误:(NO_START) |没有连接传感器，或硬件出错。”
E521010 “Laser Error:(BAD_SENSOR) | The MCM was unable to detect valid sensor data.”
“激光错误:(BAD_SENSOR) |MCM 不能检索正确的传感器数据。”
E521012 “Laser Error:(BAD_EE_VERSION) | The firmware does not recongize the sensor EEPROM
version.”
“激光错误:(BAD_EE_VERSION) |固件不能识别 EEPROM 版本。”
E521013 “Laser Error:(BAD_EE_DATA) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_DATA) |从传感器 EEPROM 读取校准数据发生错误。”
E521014 “Laser Error:(BAD_EE_SYNC) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_SYNC) |从传感器 EEPROM 读取校准数据发生错误。”
E521015 “Laser Error:(POWER_LOW) | The MCM detected that the incoming voltage level was below that
required for proper sensor opration.”
“激光错误:(POWER_LOW) |MCM 发现电压下降，导致传感器不能正常运作。”
E521017 “Laser Error:(OVER_CURR) | The MCM detect that power to the sensor was low.”
“激光错误:(OVER_CURR) |MCM 发现电压下降，导致传感器不能正常运作。”
E521060 “Laser Error:(SHORT_BUF) | The communication buffer contained fewer bytes than specified by
the length.”
“激光错误:(SHORT_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521061 “Laser Error:(LONG_BUF) | The communication buffer contained more bytes than spcified by the
length.”
“激光错误:(LONG_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521062 “Laser Error:(SHORT_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(SHORT_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521063 “Laser Error:(LONG_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(LONG_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521083 “Laser Error:(BAD_CHKSUM) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(BAD_CHKSUM) |固件从传感器 EEPROM 读取数据中发现错误。”
E521084 “Laser Error:(DUP_START) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(DUP_START) |固件从传感器 EEPROM 读取数据中发现错误。”
E521085 “Laser Error:(NO_EEPROM_SOD) | The firmware found an error while reading the sensor
EEPROM.”
“激光错误:(NO_EEPROM_SOD) |固件从传感器 EEPROM 读取数据中发现错误。”
E521086 “Laser Error:(BAD_PARM) | An invalid parameter was specified for a command.”
“激光错误:(BAD_PARM) |命令中发现无效的参数。”
E521087 “Laser Error:(BAD_DATA) | Invalid data was detected.”
“激光错误:(BAD_DATA) |发现无效数据。”
E521100 “Laser Error:(UNITS_NOT_SET) | Requested Initialzation was not done.”
“激光错误:(UNITS_NOT_SET) |未初始化状态下，被接受命令错误。”
E521102 “Laser Error:(INVALID_ALG) | The alogrithm specified for the mesurement is invalid.”
“激光错误:(INVALID_ALG) |错误的测量方法。”
E521064 “Laser Error (NO_PART) | The shadow was undetectable during measurement.”
“激光错误:(NO_PART) | 测量中检测不到阴影 “
E521065 “Laser Error:(TOOL_SLOW) | The MCM processor was unable to keep up with the frame rate.”
“激光错误:(TOOL_SLOW) |MCM 处理器不能跟上测量速度。”
E521067 “Laser Error:(ABORTED) | The MCM recived a command that aborted.”
“激光错误:(ABORTED) |MCM 被接受强行停止测量命令。”
E521070 “Laser Error:(ALG_ERR) | The firmware detected a state that should never happen.”
“激光错误:(ALG_ERR) |固件发现了不应该发生的状况。”
E521075 “Laser Error:(PRV_ERR) | During SWEEP_CMD error occuerd during next mesurement.”
“激光错误:(PRV_ERR) |检查端点(Peak)中发现前一次的端点检查错误。”
E521077 “Laser Error:(WIDE_ERR) | The gray-scale edge on the detector did not have enough contrast to
finde actual component edge.”
“激光错误:(WIDE_ERR) |检查组件间距中，发现组件间距不够长。”
E521078 “Laser Error:(SMALL_WIN) | The window parameters specify a window that is samll than 2000
micron.”
“激光错误:(SMALL_WIN) |被指定小于 2000 微米的窗口。”
E521079 “Laser Error:(WIN_BLOCKED) | The entire window is blocked.”
“激光错误:(WIN_BLOCKED) |窗口被赌塞错误。”