JUKI贴片机错误代码.pdf - 第240页

E613037 “ The nozzl e is too long. (over 0.6mm)|Please check t he nozzle in stallation status. (L3-head) ” “ 吸嘴过 长。 ( 超过 0.6mm)| 请检查吸嘴安装状态。 (L3 Head) “ E614037 “ The nozzl e is too long. (over 0.6mm)|Please check t he no…

100%1 / 464
E614033 “ATC X coordinate is abnormal. (L4-head)”
“ X 坐标参数不正确。(L4 Head) “
E615033 “ATC X coordinate is abnormal. (R1-head)”
“ X 坐标参数不正确。(R1 Head) “
E616033 “ATC X coordinate is abnormal. (R2-head)”
“ X 坐标参数不正确。(R2 Head) “
E617033 “ATC X coordinate is abnormal. (R3-head)”
“ X 坐标参数不正确。(R3 Head) “
E618033 “ATC X coordinate is abnormal. (R4-head)”
“ X 坐标参数不正确。(R4 Head) “
E611034 “ATC Y coordinate is abnormal. (L1-head)”
“ Y 坐标参数不正确。(L1 Head) “
E612034 “ATC Y coordinate is abnormal. (L2-head)”
“ Y 坐标参数不正确。(L2 Head) “
E613034 “ATC Y coordinate is abnormal. (L3-head)”
“ Y 坐标参数不正确。(L3 Head) “
E614034 “ATC Y coordinate is abnormal. (L4-head)”
“ Y 坐标参数不正确。(L4 Head) “
E615034 “ATC Y coordinate is abnormal. (R1-head)”
“ Y 坐标参数不正确。(R1 Head) “
E616034 “ATC Y coordinate is abnormal. (R2-head)”
“ Y 坐标参数不正确。(R2 Head) “
E617034 “ATC Y coordinate is abnormal. (R3-head)”
“ Y 坐标参数不正确。(R3 Head) “
E618034 “ATC Y coordinate is abnormal. (R4-head)”
“ Y 坐标参数不正确。(R4 Head) “
E611037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L1-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L1 Head) “
E612037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L2-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L2 Head) “
E613037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L3-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L3 Head) “
E614037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L4-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L4 Head) “
E615037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R1-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R1 Head) “
E616037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R2-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R2 Head) “
E617037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R3-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R3 Head) “
E618037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R4-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R4 Head) “
E611038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L1-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L1 Head) “
E612038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L2-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L2 Head) “
E613038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L3-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L3 Head) “
E614038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L4-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L4 Head) “
E615038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R1-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R1 Head) “
E616038”The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R2-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R2 Head) “
E617038”The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R3-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R3 Head) “
E618038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R4-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R4 Head) “
E611042 “A shadow is detected while nozzle detection after returning nozzles. (L1-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L1 Head) “
E612042 “A shadow is detected while nozzle detection after returning nozzles. (L2-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L2 Head) “
E613042 “A shadow is detected while nozzle detection after returning nozzles. (L3-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L3 Head) “
E614042 “A shadow is detected while nozzle detection after returning nozzles. (L4-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L4 Head) “
E615042 “A shadow is detected while nozzle detection after returning nozzles. (R1-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R1 Head) “
E616042 “A shadow is detected while nozzle detection after returning nozzles. (R2-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R2 Head) “
E617042 “A shadow is detected while nozzle detection after returning nozzles. (R3-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R3 Head) “
E618042 “A shadow is detected while nozzle detection after returning nozzles. (R4-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R4 Head) “
E611047 “The cylinder to which the nozzle is returned is not appropriate. (L1-head)”
“ 放回吸嘴的圆筒位置不对。(L1 Head) “
E612047 “The cylinder to which the nozzle is returned is not appropriate. (L2-head)”
“ 放回吸嘴的圆筒位置不对。(L2 Head) “
E613047 “The cylinder to which the nozzle is returned is not appropriate. (L3-head)”
“ 放回吸嘴的圆筒位置不对。(L3 Head) “
E614047 “The cylinder to which the nozzle is returned is not appropriate. (L4-head)”
“ 放回吸嘴的圆筒位置不对。(L4 Head) “
E615047 “The cylinder to which the nozzle is returned is not appropriate. (R1-head)”
“ 放回吸嘴的圆筒位置不对。(R1 Head) “
E616047 “The cylinder to which the nozzle is returned is not appropriate. (R2-head)”
“ 放回吸嘴的圆筒位置不对。(R2 Head) “
E617047 “The cylinder to which the nozzle is returned is not appropriate. (R3-head)”
“ 放回吸嘴的圆筒位置不对。(R3 Head) “
E618047 “The cylinder to which the nozzle is returned is not appropriate. (R4-head)”
“ 放回吸嘴的圆筒位置不对。(R4 Head) “