JUKI贴片机错误代码.pdf - 第70页
“ XY 轴发生错误。 ” [Cause] An error occurred while XY axes were traveling. [Treatment] Please contact our technical serv ice dept. for information. E301057 “ An error on Z axis occurred ” “ Z 轴发生错误。 ” [Cause] An error occurre…
In 2030, Vacuum Calibration unit can be set only for R1 through R4.
[Treatment]
Please set to ATC of R1 through R4.
E301051 “Vacuum Calibration can be et only for small-diameter nozzles. | (Settable range : 1 - %d)”
“对于该 ATC 不能设置真空校准。”
[Cause]
The Vacuum Calibration unit can not be set other ATC than the ATC of small nozzles.
|The maximum settable ATC number
[Treatment]
Please set the unit for the ATC of small nozzles.
E301052 “Any heads have not been specified”
“没有指定 Head。”
[Cause]
You did not specify a head to be measured.
[Treatment]
Please specify a head to measure.
E301053 “The Changer table can not be installed on the rear side since MTC/MTS have been selected”
“因 MTC/MTS 已被选择，不能把送料器台车安装在后侧。”
[Cause]
You can not use the changer table on the rear side when MTC or MTS is set to use.
[Treatment]
Please disable MTC or MTS when you use the changer table on the rear side.
E301054 “MTC/MTS can not be connected to 2000 series machines at the same time”
不能同时连接 MTC 和 MTS。”
[Cause]
MTC and MTS can not be set at the same time.
[Treatment]
Please disable one of them.
E301055 “An error on axes occurred”
“轴发生错误。”
[Cause]
An error occurred while axes were traveling.
[Treatment]
Please contact our technical service dept. for information.
E301056 “An error on XY axes occurred”
“XY 轴发生错误。”
[Cause]
An error occurred while XY axes were traveling.
[Treatment]
Please contact our technical service dept. for information.
E301057 “An error on Z axis occurred”
“Z 轴发生错误。”
[Cause]
An error occurred while Z axis was traveling.
[Treatment]
Please contact our technical service dept. for information.
E301058 “ Specified 508 nozzle has not been assigned yet. Please execute nozzle assignment”
”没有安装指定的 508 吸嘴。|请安装吸嘴。”
[Cause]
508 nozzle is necessary to auto-teach MTC shuttle pick position to the machine, but the 508 nozzle
has not been assigned yet..
[Treatment]
Please assign the 508 nozzle, then try auto-teaching.
E301059 “It was impossible to learn the height. | Please check out the vacuum value”
”不能取得高度。|请检查一下真空值。”
[Cause]
An abnormal matter happened while learning the height by vacuum.
[Treatment]
Please check and see if the vacuum pressure is correct.
E301060 “DTS/MTS can not be connected to 2000 series machines at the same time”
“不能同时连接 DTS 和 MTS。”
[Cause]
DTS and MTS can not be set at the same time.
[Treatment]
Please disable one of them.
E301061 “Feeder float detector can not be set only out position”
“传送带浮动传感器不能只安装在外侧。”
[Cause]
You can not use the outer feeder float detectors only.
[Treatment]
Please use the inner feeder float detectors only or use all the detectors at once.
E301062 “There is no head that can move to specified position.”
“不存在可以移到指定位置的吸嘴。”
W301063 “Selected MTC/MTS is not connected.”
“已被选用的 MTC/MTS 处于脱机状态。”
E301064 “MTS is in the supply state.”
“MTS 处于补充状态。”
E301065 “%s ||Specified nozzle data has not been registered.|Please register nozzle data.”
“%s ||吸嘴信息没有注册。|请注册吸嘴信息。”
E301066 “The nozzle no. is invalid.”
“无效的吸嘴号。”
E301067 “A drive can not be access.|Please check the FD”
“不能访问 A 驱动器。|请确认一下软盘。”
E301068 “Because the right head is disable, it can not be measured.”
“因为右 Head 处于不使用状态，所以不能进行测量。”
E301069 “Input value exceeds predetermined data range.”
“输入数据超过范围。”
E301070 “It can not be set the small nozzle on a large ATC.”
“大型 ATC 上不能安装小型吸嘴。”
E301071 “The SemiAuto Trash box is not at the abandonment position.|Please set the SemiAuto Trash box at
the abandonment position.”
“半自动废弃盒不在废弃位置。|请把半自动废弃盒设置在废弃位置。”
E301072 “The production program has not read.”
“不能读取生产程序。”
E301073 “An error occurred while BOC alignment.”
“BOC 校准发生错误。”
E301074 “An error occurred while BOC Mark Correct.”
“BOC 标记校正发生错误。”
W301075 “Because the nozzle data[ %s ] is initial data, it can not be delete.”
“因为被选吸嘴的信息[ %s ]是初始数据，不能删除。”
W301076 “Input value exceeds the simultaneous BOC mark recognition limit.|Please check out the Y value.”
“输入值超过了同时识别 BOC 标记的范围。|请检查一下 Y 坐标值。”