JUKI贴片机错误代码.pdf - 第51页
E290026 “ There is no MTS stacker .” “ MTS 托盘 存储箱不存在。 ” E290027 “ MTS failed in drawing out the tray .” “ MTS 取出托盘失败。 ” E290028 “ MTS device is set in unused by the setup .” “ 在设置 中， MTS 装置没有被选用。 ” E290029 “ Transmit err…
E290009 “Can not mark-teaching by R OCC. L OCC use,please.”
“右侧 OCC 不能示教标记，请使用左侧 OCC。”
E290010 “DTS cannot be executed.”
“不能运行 DTS。”
E290011 “DTS is not initialized.”
“DTS 没有初始化。”
E290012 “DTS safety cover opens.”
“DTS 安全盖被打开。
E290013 “DTS is in the state of supply.”
“DTS 处于补充状态。”
E290014 “DTS failed in drawing out the tray.”
“DTS 取出托盘失败。”
E290015 “DTS device is set in unused by the setup.”
“在设置中，DTS 装置没有被选用。”
E290016 “It is not possible to move to specified position with this device.”
“这个设备不能移到指定坐标上。”
E290017 “Check sum error of template data. Please teaching try again.”
“检查模板数据合计出错。请再次示教修改。”
E290020 “There is no power supply of MTS.”
“没有打开 MTS 电源。”
E290021 “MTS is stopping the emergency.”
“MTS 被紧急停止。”
E290022 “MTS is not initialized.”
“没有初始化 MTS。”
E290023 “MTS is in the state of off-line.”
“没有连接 MTS。”
E290024 “MTS stacker cover opens.”
“MTS 托盘存储箱盖被打开。”
E290025 “MTS is in the state of supply.”
“MTS 处于补充状态。”
E290026 “There is no MTS stacker.”
“MTS 托盘存储箱不存在。”
E290027 “MTS failed in drawing out the tray.”
“MTS 取出托盘失败。”
E290028 “MTS device is set in unused by the setup.”
“在设置中，MTS 装置没有被选用。”
E290029 “Transmit error of template data. Please teaching try again.”
“模板数据传输发生错误。请再次示教修改。”
E290030 “The bank mark recognition error (MTS). | Teaching is aborted.”
“识别台架标记出错(MTS)。| 停止运行。”
Q290500 “It is not possible to move to specified position with this device. | Please push 'No' when you
discontinue 'Yes' when the teaching is started from the current position”
“这个设备不能移到指定坐标上。|从当前位置开始示教，请按[是]﹔停止，请按[否]。”
[Cause]
You can not move to the previously set coordinates with the device selected by HOD. You are asked
if to resume the teaching from the current position.
[Treatment]
If you want to continue the process, press “Yes”. If not, press “No”.
Q290501 “The teaching operation is executed. Please confirm safety. | Please push 'No' when you discontinue
'Yes' when executing this”
“运行示教操作，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since this operation takes axis traveling.
[Treatment]
If you want to continue the process, press 'Yes'. If not, press 'No'.
Q290502 “The position cannot be corrected. | Please push 'No' when you discontinue 'Yes' when correction is
not considered and teaching is executed”
“不能运行坐标校正。|不考虑校正继续运行示教，请按[是]﹔停止，请按[否]。”
[Cause]
You need to correct the coordinates in order to teach the coordinates to the machine accurately, but
the Mark recognition that is necessary for the coordinate correction failed for some reason. You are
asked if to continue the teaching although the accurate teaching cannot be expected if you continue
the process..
[Treatment]
If you want to continue the process, press 'Yes'. If not, press 'No'.
Q290503 “The mark has already been registered. Do you overwrite?”
“已经存在标记，是否覆盖保存？”
[Cause]
There is a mark data left, which was registered before. You are asked if to overwrite the data.
[Treatment]
If you want to overwrite the data, press 'Yes'. If not, press 'No'.
E291000 “Conveyor already operated, it is not possible to operation”
“因为正在运行传送操作，所以不能执行。”
[Cause]
The conveyor has already been in operation.
[Treatment]
Please wait for a while and try again.
E291001 “The origin point return is non-completion. | Please operate again after completing the origin point
return”
“没有执行返回原点。|请执行返回原点后，再次操作。”
[Cause]
Home returning has not been complete yet.
[Treatment]
Please press the ORIGIN button to perform the Home returning, and try again.
E291002 “The axis cannot be moved to escape point. | Execution is aborted”
“轴不能移到等待位置。|停止运行。”
[Cause]
Failed to move the axis to the escape point.
[Treatment]
Please check and see if the axis works properly with Manual control.
E291003 “The conveyor cannot be moved. | Execution is aborted”
“不能执行传送。|停止运行。”
[Cause]
The conveyor did not work for some reason.
[Treatment]
Please check and see if the conveyor works properly with Manual control.
E291004 “The conveyor became a time-out. | Execution is aborted”
“传送超过时间。|停止运行。”
[Cause]
PWB conveying had a time-out error.
[Treatment]