JUKI贴片机错误代码.pdf - 第58页
Q291502 “ The BOC alignment is ex ecuted. P lease confirm safety. | Please push 'No' when discontinui ng. 'Yes' when continuing ” “ 执行 BOC 校 准，请注意安全。 | 执行，请按 [ 是 ] ﹔停 止，请按 [ 否 ] 。 ” [Cause] You are as…
E291029 “MTC is not power on.”
“MTC 电源未打开。”
E291030 “MTC is not online.”
“没有连接 MTC。”
E291031 “MTC initialize not done.”
“MTC 未初始化。”
E291032 “MTC is in the supply state.”
“MTC 处于补充状态。”
E291033 “MTC conveyor initialize not done.”
“MTC 传送没有进行初始化。”
E291034 “MTC Emergency Switch is Pressed.”
“MTC 处于紧急停止状态。”
E291035 “The PWB data is not set.”
“未输入基板数据。”
E291036 “The Coplanarity is set in unused by the setup. “
“在设置中，共面检测器没有被选用。”
E291037 “The BAD mark data is not set.| Operation is aborted.”
“未设置坏板标记数据。|停止执行。 “
E291038 “The BAD mark sensor is set in unused by the setup. “
“在设置中，坏板标记传感器没有被选用。 “
Q291500 “The BOC mark recognition error. | Please push 'No' when discontinuing. 'Yes' when continuing”
“识别 BOC 标记失败。|继续，请按[是]﹔停止，请按[否]。”
[Cause]
The BOC mark(s) could not be recognized by VCS.
[Treatment]
There is a possibility that the BOC mark(s) could not be taught to the machine properly.
Q291501 “Operation interruption. | Please push 'No' when discontinuing. 'Yes' when continuing”
“被用户中断。|继续，请按[是]﹔停止，请按[否]。”
[Cause]
The operation was aborted since STOP button was pressed.
[Treatment]
If you want continue the operation, press 'Yes'. If not, press 'No'.
Q291502 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291503 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291504 “The BOC alignment is executed. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“执行 BOC 校准，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291505 “Unit is moved to escape point. Please confirm safety. | Please push 'No' when discontinuing. 'Yes'
when continuing”
“轴往等待位置移动，请注意安全。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check since the operation takes axis traveling.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291506 “Conveyor width is moved. Please remove handknob and PWB from conveyor. | Please push 'No'
when discontinuing. 'Yes' when continuing”
“移动基板幅宽，请取下基板和摇把。|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the safety check by removing PWBs and a handknob from the conveyor
since the conveyor width is adjusted.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291507 “The origin point return of automatic conveyor width adjustment is non-completion. Continue
anyway? | Please push 'No' when discontinue. 'Yes' when continuing”
“没有结束调整基版宽度的返回原点。是否执行返回原点？|执行前，请取下基板和摇把。
|执行，请按[是]﹔停止，请按[否]。”
[Cause]
You are asked if to perform the Home returning of the Auto. PWB Width Alignment Control since its
Home returning has not been complete yet.
[Treatment]
If you want to continue the operation, press 'yes'. If not, press 'No'.
Q291508 “MTC Conveyor width is moved,too? | Please push 'No' when discontinue 'Yes' when continuing.”
“是否也移动 MTC 装置的基板幅宽？|执行，请按[是]﹔停止，请按[否]。”
I291509 “Please set online for MTC.”
“请联接 MTC。”
Q291510 “Conveyor width is moved. Does it move, although the vacuum table is attached? | Please push 'No'
when discontinue 'Yes' when continuing.”
“ 虽然真空器已被安装，是否也移动基板幅宽？|执行，请按[是]﹔停止，请按[否]。 “
E292000 “No registered data”
“没有注册数据。”
[Cause]
The following procedures were taken place when the number of the registered issue of Mark Database
is zero.
1. Press [Rename(C)] button or [Delete(D)] button on the Mark Database Management screen.
2. Press [Replace(A)] button on the Registration Mark Database screen.
3. Press [Copy(C)] button on the Vision Copy screen.
[Treatment]
The procedures above can not be performed when there is no registry in the Mark Database.
E292001 “Please select the mark”
“请选择标记。”
[Cause]
1. Although [Rename (C)] button or [Delete(D)] button screen were pressed on the Mark Database
Management screen, there is no selected mark to be an object of the action.
2. Although [Copy(C)] button was pressed on the Vision Copy screen, there is no selected mark to
be an object of the action.
[Treatment]
Please select a mark to be an object of each action.