JUKI贴片机错误代码.pdf - 第452页
E6352 “ Data before distributi on cannot be read. “ " 不能读分配前的数据。 " E6353 “ Distribution opti on cannot be read. “ " 不能读分配选项。 " E6354 Reference table cannot be read. " 不能读资料表。 " [Cause] Loadi…
E6114 Setting of room coefficient is out of range.
[Cause]
An excessive value was specified for the redundant factor.
[Deal]
Enter a value within the range, 0 to 100.
E6250 “Area cannot be secured. “
"区域不能被保护。"
E6251 “INI file cannot be read. “
"不能读 INI 文件。"
E6252 “Distributed data cannot be read. “
"不能读分配数据。"
E6253 “Data combining failed. “
"数据结合失败。"
E6254 “Combining of data failed because data are mutually exclusive. “
"由于数据相互排斥数据结合失败。"
E6255 “Combined data cannot be output. “
"不能输出组合数据。"
E6300 “Setting of number of programs etc. failed. “
"设置程序数量等失败。"
E6350 Area cannot be secured.
"区域不能被保护。"
[Cause]
Allocating the memory for EPU was failed. Allocating the memory for G3h and G3N was failed.
[Deal]
Exit from other applications and retry the process.
E6351 File read failed.
"不能读预定程序目录。"
[Cause]
Loading files, G3H and GXL, was failed. Insufficient free space on the memory or any failure on the
disk is suspected.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applica
tions and retry installation.
E6352 “Data before distribution cannot be read. “
"不能读分配前的数据。"
E6353 “Distribution option cannot be read. “
"不能读分配选项。"
E6354 Reference table cannot be read.
"不能读资料表。"
[Cause]
Loading files, OPTIM.INI and CYCLE.INI. It is suspected that the installation was failed or any
failure occurred on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6355 “Station information cannot be read. “
"不能读位置信息。"
E6356 Resource data cannot be read.
"不能读资源数据。"
[Cause]
Loading a files HLCSETUP.INI. It is suspected that the installation was failed or any failure occurred
on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6357 “Permanent data cannot be read. “
"不能读永久数据。"
E6358 “Station order conflicts with the optimization that was excuted. “
"优化的位置顺序有冲突."
E6400 “Component in program and permanent component are improperly positioned. “
"在程序中的组件和永久性组件位置不正确."
E6402 “PWB data is not completed. “
"基板数据不完全。"
E6403 Component data are incomplete. (No.%d)
"贴片数据不完全。"
[Cause]
The mounting data is incomplete.
[Deal]
Complete the mounting data.
E6404 Component data is not completed.
"组件数据不完全。"
[Cause]
The part data where the mounting position is allocated is incomplete.
[Deal]
Complete the part data.
E6405 Pick data are incomplete.
"吸取数据不完全。"
[Cause]
The pick data is incomplete.
[Deal]
Complete the pick data.
E6406 “Vision data is not completed. “
"图像数据不完全。"
E6407 “Specified number supplied exceeds resource. “
"提供的特殊数字超过资源数。"
E6408 “Assigned placement data exist in plural number of stations. “
"指定贴片数据存在于复数位置。"
E6409 “Assigned pick data exist in multiple stations. “
"指定挑选数据存在于多个位置。"
E6420 “Component in %dth program is overlapped with permanent component. “
"在%dth 程序中的组件被永久组件覆盖 "
E6422 “PWB data in %dth program is not completed. “
"在％dth 程序的基板 B 数据不完全。"
E6423 “Placement data in %dth program is not completed. “
"在％dth 程序的贴片数据不完全。"
E6424
“Component data in %dth program is not completed. “
"在％dth 程序的组件数据不完全。"
E6425 “Pick data in %dth program is not completed. “
"在%dth 程序中的吸取数据不完全。"
E6426 “Vision data in %dth program is not completed. “