JUKI贴片机错误代码.pdf - 第168页

E602540 “ Axi s Driver:| YR-axis. coordi nate exceeds a movable range .” “ YR 轴错误 : | 超过移动范围。 ” E602141 “ Axis Driver:| X-axis. The da c out error exceeded the limit .” “ X 轴错误 |DAC 输出超出 界限。 ” E602241 “ Axis Driver:| Y-a…

100%1 / 464
E602236 “Axis Driver:| Y-axis. The velocity error exceeded the limit.|(Check the power supply for the
possibilities of low power supply voltage.)”
“Y 轴错误: 速度误差超过界限。|(可能电压不足，请检查电压。)”
E602536 “Axis Driver:| YR-axis.The velocity error exceeded the limit.|(Check the power supply for the
possibilities of low power supply voltage.)”
“YR 轴错误: 速度误差超过界限。|(可能电压不足，请检查电压。)”
E602137 “Axis Driver:| X-axis. The motor encoder is abnormal.|(There is a possibility that the motor
damaged.)”
“X 轴错误: |马达编码器异常。|(可能马达损坏。)”
E602237 “Axis Driver:| Y-axis. The motor encoder is abnormal.|(There is a possibility that the motor
damaged.)”
“Y 轴错误: |马达编码器异常。|(可能马达损坏。)”
E602537 “Axis Driver:| YR-axis.The motor encoder is abnormal.|(There is a possibility that the motor
damaged.)”
“YR 轴错误: |马达编码器异常。|(可能马达损坏。)”
E602138 “Axis Driver:| X-axis. The position error exceeded the limit.”
“X 轴错误: |位置偏移量超过界限。”
E602238 “Axis Driver:| Y-axis. The position error exceeded the limit.”
“Y 轴错误: |位置偏移量超过界限。”
E602139 “Axis Driver:| X-axis. Amp fault error.”
“X 轴错误: |Amp 故障。”
E602239 “Axis Driver:| Y-axis. Amp fault error.”
“Y 轴错误: |Amp 故障。”
E602140 “Axis Driver:| X-axis. coordinate exceeds a movable range.”
“X 轴错误: |超过移动范围。”
E602240 “Axis Driver:| Y-axis. coordinate exceeds a movable range.”
“Y 轴错误: |超过移动范围。”
E602340 “Axis Driver:| XR-axis. coordinate exceeds a movable range.”
“XR 轴错误: |超过移动范围。”
E602440 “Axis Driver:| YC-axis. coordinate exceeds a movable range.”
“YC 轴错误: |超过移动范围。”
E602540 “Axis Driver:| YR-axis. coordinate exceeds a movable range.”
“YR 轴错误: |超过移动范围。”
E602141 “Axis Driver:| X-axis. The dac out error exceeded the limit.”
“X 轴错误 |DAC 输出超出界限。”
E602241 “Axis Driver:| Y-axis. The dac out error exceeded the limit.”
“Y 轴错误 |DAC 输出超出界限。”
E602541 “Axis Driver:| YR-axis. The dac out error exceeded the limit.”
“YR 轴错误 |DAC 输出超出界限。”
E602560 “Axis Driver:| YR-axis. The position error exceeded the limit.”
“YR 轴错误: |位置偏移量超过界限。”
E603110 “Axis Driver:| Z1-axis parameter error.”
“ Z1 轴错误: 参数错误。”
E603210 “Axis Driver:| Z2-axis parameter error.”
“ Z2 轴错误: 参数错误。”
E603310 “Axis Driver:| Z3-axis parameter error.”
“ Z3轴错误: 参数错误。”
E603410 “Axis Driver:| Z4-axis parameter error.”
“ Z4轴错误: 参数错误。”
E603510 “Axis Driver:| RZ1-axis parameter error.”
“ RZ1轴错误: 参数错误。”
E603610 “Axis Driver:| RZ2-axis parameter error.”
“ RZ2轴错误: 参数错误。”
E603710 “Axis Driver:| RZ3-axis parameter error.”
“ RZ3轴错误: 参数错误。”
E603810 “Axis Driver:| RZ4-axis parameter error.”
“RZ4轴错误: 参数错误。”
E603011 “Axis Driver:| Z-axis invalid unit.”
“Z 轴错误: 无效单元。”
E603112 “Axis Driver:| Z1-axis failed originating.”
“ Z1 轴错误: 回原点失败。”
E603212 “Axis Driver:| Z2-axis failed originating.”
“ Z2 轴错误: 回原点失败。”
E603312 “Axis Driver:| Z3-axis failed originating.”
“ Z3 轴错误: 回原点失败。”
E603412 “Axis Driver:| Z4-axis failed originating.”
“ Z4 轴错误: 回原点失败。”
E603512 “Axis Driver:| RZ1-axis failed originating.”
“ RZ1 轴错误: 回原点失败。”
E603612 “Axis Driver:| RZ2-axis failed originating.”
“ RZ2 轴错误: 回原点失败。”
E603712 “Axis Driver:| RZ3-axis failed originating.”
“R Z3 轴错误: 回原点失败。”
E603812 “Axis Driver:| RZ4-axis failed originating.”
“ RZ4 轴错误: 回原点失败。”
E603113 “Axis Driver:| Z1-axis error.|Servo power is OFF.”
“ Z1轴错误: 伺服电源被关闭”
E603213 “Axis Driver:| Z2-axis error.|Servo power is OFF.”
“ Z2 轴错误: 伺服电源被关闭”
E603313 “Axis Driver:| Z3-axis error.|Servo power is OFF.”
“ Z3 轴错误: 伺服电源被关闭”
E603413 “Axis Driver:| Z4-axis error.|Servo power is OFF.”
“ Z4 轴错误: 伺服电源被关闭”
E603513 “Axis Driver:| RZ1-axis error.|Servo power is OFF.”
“RZ1 轴错误: 伺服电源被关闭”
E603613 “Axis Driver:| RZ2-axis error.|Servo power is OFF.”
“RZ2 轴错误: 伺服电源被关闭”
E603713 “Axis Driver:| RZ3-axis error.|Servo power is OFF.”
“RZ3 轴错误: 伺服电源被关闭”
E603813 “Axis Driver:| RZ4-axis error.|Servo power is OFF.”
“RZ4 轴错误: 伺服电源被关闭”