JUKI贴片机错误代码.pdf - 第40页
E242517 “ The nozzle cannot be exchanged. “ “ 交换吸嘴失败。 ” E242518 “ The nozzle cannot be installed .” “ 安装吸 嘴失败。 ” 2 E242519 “ There is no head which can be moved to the component pic kup pos ition .” “ Head 不能移到组件吸取坐标。 ” …
E242503 “Axis movement error (YC axis limit error)”
“轴移动发生错误(YC 轴界限错误)”
E242504 “Axis movement error (Z axis limit error)”
“轴移动发生错误(Z 轴界限错误)”
E242505 “Axis movement error (T axis limit error)”
“轴移动发生错误(T 轴界限错误)”
E242506 “Axis movement error (XY axis driver error)”
“轴移动发生错误(XY 轴驱动错误)”
E242507 “Axis movement error (YC axis driver error)”
“轴移动发生错误(YC 轴驱动错误)”
E242508 “Axis movement error (Z axis driver error)”
“轴移动发生错误(Z 轴驱动错误)”
E242509 “Axis movement error (T axis driver error)”
“轴移动发生错误(T 轴驱动错误)”
E242510 “The vacuum pressure cannot be measured.”
“取得真空压发生错误。(I/O 驱动错误)”
E242511 “No component.(Retry over of picking.)|Please confirm the existence of components.”
“无组件。(重试结束)|请确认一下组件是否存在。”
E242512 “Laser measurement error (ONCE measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(ONCE 测量) | 代码 = %d (请查阅操作手册。)”
E242513 “Laser measurement error (Height measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(高度测量) | 代码 = %d (请查阅操作手册。)”
E242514 “Laser measurement error (SWEEP measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(SWEEP 测量) | 代码 = %d (请查阅操作手册。)”
E242515 “There is no %d nozzle. “
“%d 号吸嘴不存在。”
E242516 “The nozzle cannot be returned. “
“归还吸嘴失败。”
E242517 “The nozzle cannot be exchanged. “
“交换吸嘴失败。”
E242518 “The nozzle cannot be installed.”
“安装吸嘴失败。”
2
E242519 “There is no head which can be moved to the component pickup position.”
“Head 不能移到组件吸取坐标。”
E242520 “Component data error”
“组件数据错误。”
E242521 “The IC collection belt is unused by the setup. “
“在设置中，IC 回收器没有被选用。”
E242522 “The IC collection belt is fullness.”
“IC 回收器已被装满。”
E242523 “The chip standing was detected.”
“查出芯片站立。”
E242524 “The height of laser was not able to be measured from range.|Please confirm the height of
component.”
“不能检测在标准范围内的激光高度。|请确认一下组件高度。”
E242525 “The height of components was measured with 0mm or less.|Please confirm the height of laser.”
“测量组件高度结果为负值。|请确认一下组件高度。”
E242526 “Laser measurement error (MCM driver error) “
“激光测量发生错误(MCM 驱动错误) “
E242527 “Because the lower bound of being able the axis movement had been exceeded,|the height of the
laser was not able to be measured.”
“因为超过轴移动范围的下限，不能测量激光高度。”
E242528 “Could not change of mode for the chip verification system.”
“变更数值检查装置的测量模式失败。”
E242529 “Chip verification detection error.”
“数值检查装置测量发生错误。”
E242530 “The chip verification system is unused by the setup. “
“在设置中，数值检查装置没有被选用。”
E242531 “Component angle exceeds limit value.”
“组件过于倾斜。”
E242532 “Component size is too big.”
“组件外形尺寸过于偏大。”
E242533 “Component size is too small.”
“组件外形尺寸过于偏小。”
E242534 “Cannot recognize component.”
“不能识别组件。”
E242535 “Lead pitch of %s side is not conform.”
“%s 的引脚间距不一致。”
E242536 “Cannot recognize lead of %s side.”
“不能识别%s 的引脚间距。”
E242537 “Error has occurred during VCS measurement.|Code: %ld”
“VCS 测量组件发生错误。|代码: %ld”
E242538 “MTC is not power on.”
“没有打开 MTC 电源。”
E242539 “MTC is not online.”
“没有连接 MTC。”
E242540 “MTC is in the supply state.”
“MTC 处于补充状态。”
E242541 “MTC is disable.”
“不能使用 MTC。”
E242542 “MTC Emergency Switch is Pressed.”
“MTC 处于紧急停止状态。”
E242543 “MTC initialize not done.”
“未初始化 MTC。”
E242544 “MTC failed to a supply of a component.”
“MTC 供给组件失败。”
E242545 “The component remainder number is 0.”
“组件剩余数为 0。”
E242546 “TF driver error. |Code: %ld”