JUKI贴片机错误代码.pdf - 第187页

E605331 “ Axi s Driver:| AWC status error .” “ 自动调 整基板宽度发生状态错误。 ” E605531 “ Axi s Driver:| Center motor status error .” “ 中心马 达发生状态错误。 ” E605631 “ Axi s Driver:| Right Cen ter motor status error .” “ 右中心 马达发生状态错误。 ” E605…

100%1 / 464
E605312 “Axis Driver:| AWC failed originating.”
“自动调整基板宽度的返回原点失败。”
E605113 “Axis Driver:| Support table error.|Servo power is OFF.”
“支撑台的电源被关闭。”
E605213 “Axis Driver:| Right Support table error.|Servo power is OFF.”
“右支撑台的电源被关闭。”
E605313 “Axis Driver:| AWC error.|Servo power is OFF.”
“自动调整基板宽度的电源被关闭。”
E605513 “Axis Driver:| Center motor error.|Servo power is OFF.”
“中心马达的电源被关闭。”
E605613 “Axis Driver:| Right Center motor error.|Servo power is OFF.”
“右中心马达的电源被关闭。”
E605119 “Axis Driver:| Support table error.|Stopper is locked.”
“支撑台的制动器被锁定。”
E605219 “Axis Driver:| Right Support table error.|Stopper is locked.”
“右支撑台的制动器被锁定。”
E605130 “Axis Driver:| XMP error occurred on support table.”
“支撑台发生 XMP 错误。”
E605230 “Axis Driver:| XMP error occurred on right support table.”
“右支撑台发生 XMP 错误。”
E605330 “Axis Driver:| XMP error occurred on AWC.”
“自动调整基板宽度发生 XMP 错误。”
E605530 “Axis Driver:| XMP error occurred on center motor.”
“中心马达发生 XMP 错误。”
E605630 “Axis Driver:| XMP error occurred on right center motor.”
“右中心马达发生 XMP 错误。”
E605131 “Axis Driver:| Support table status error.”
“支撑台发生状态错误。”
E605231 “Axis Driver:| Right Support table status error.”
“右支撑台发生状态错误。”
E605331 “Axis Driver:| AWC status error.”
“自动调整基板宽度发生状态错误。”
E605531 “Axis Driver:| Center motor status error.”
“中心马达发生状态错误。”
E605631 “Axis Driver:| Right Center motor status error.”
“右中心马达发生状态错误。”
E605132 “Axis Driver:| Support table failed motion start.”
“支撑台启动失败。”
E605232 “Axis Driver:| Right Support table failed motion start.”
“右支撑台启动失败。”
E605332 “Axis Driver:| AWC failed motion start.”
“自动调整基板宽度启动失败。”
E605532 “Axis Driver:| Center motor failed motion start.”
“中心马达启动失败。”
E605632 “Axis Driver:| Right Center motor failed motion start.”
“右中心马达启动失败。”
E605133 “Axis Driver:| Support table failed motion stop.”
“支撑台停止失败。”
E605233 “Axis Driver:| Right Support table failed motion stop.”
“右支撑台停止失败。”
E605333 “Axis Driver:| AWC failed motion stop.”
“自动调整基板宽度停止失败。”
E605533 “Axis Driver:| Center motor failed motion stop.”
“中心马达停止失败。”
E605633 “Axis Driver:| Right Center motor failed motion stop.”
“右中心马达停止失败。”
E606010 “Axis Driver:| XH-axis parameter error.”
“ XH 轴错误: |参数错误。”
E606012 “Axis Driver:| XH-axis failed originating.”
“ XH 轴错误: |返回原点失败。”
E606013 “Axis Driver:| XH-axis error.|Servo power is OFF.”
“ XH 轴错误: |司服电源被关闭。”
E606014 “Axis Driver:| XH-axis error.|Driver alarm.”
“ XH 轴错误: |发生驱动警报。”
E606015 “Axis Driver:| XH-axis error.|Amp disabled.”
“ XH 轴错误: |Amp 失效。”
E606016 “Axis Driver:| XH-axis error.|Position of Z-axis is low.”
“ XH 轴错误: |因 Z 轴下降而不能正常运行。”
E606020 “Axis Driver:| XH-axis gain setting failed.”
“ XH 轴错误: |设置增值参数失败。”
E606030 “Axis Driver:| XMP error occurred on XH-axis.”
“ XH 轴错误: |XMP 错误。”
E606031 “Axis Driver:| XH-axis status error.”
“ XH 轴错误: |状态错误。”
E606032 “Axis Driver:| XH-axis failed motion start.”
“ XH 轴错误: |启动失败。”
E606033 “Axis Driver:| XH-axis failed motion stop.”
“ XH 轴错误: |停止失败。”
E610001 “An error occurred when opening the ATC slide plate”
“打开 ATC 滑板出错。”
[Cause]
An error occurred when trying to open the ATC slide plate. The error occurred in the Data
communication in the machine.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610002 “An error occurred when shutting the ATC slide plate”
“关闭 ATC 滑板出错。”
[Cause]
An error occurred when trying to open the ATC slide plate. The error occurred in the Data