JUKI贴片机错误代码.pdf - 第43页
“ DTS 处于补充状态。 ” E242612 “ DTS failed in drawing out the tray .” D T S 取出托盘失败。 ” E242613 “ It failed in creating li ghting data .” “ 建立 VCS 照明数据失败。 ” E242614 “ The optimum value of lighting data was unacquirable .” “ 不能取 …
“TF 驱动错误 |代码: %ld”
E242547 “MTS is not power on.”
“没有打开 MTS 电源。”
E242548 “MTS is not online.”
“没有连接 MTS。”
E242549 “MTS is disable.”
“不能使用 MTS。”
E242600 “MTS failed to pull a tray.”
“MTS 取出托盘失败。”
E242601 “MTS failed to store a tray.”
“MTS 储存托盘失败。”
E242602 “MTS cannot move because of cover opening.”
“打开主机盖时，MTS 停止动作。”
E242603 “The door of MTS opens.”
“MTS 的门被打开。”
E242604 “The stacker of MTS is empty.”
“MTS 没有安装托盘存储箱。”
E242605 “MTS Emergency Switch is Pressed.”
“MTS 处于紧急停止状态。”
E242606 “MTS initialize not done.”
“未初始化 MTS。”
E242607 “DTS is disable.”
“不能使用 DTS。”
E242608 “DTS cannot be executed.”
“DTS 不能运行。”
E242609 “DTS is not initialized.”
“未初始化 DTS。”
E242610 “DTS safety cover opens.”
“DTS 安全盖被打开。”
E242611 “DTS is in the state of supply.”
“DTS 处于补充状态。”
E242612 “DTS failed in drawing out the tray.”
DTS取出托盘失败。”
E242613 “It failed in creating lighting data.”
“建立 VCS 照明数据失败。”
E242614 “The optimum value of lighting data was unacquirable.”
“不能取得照明数据优化值。”
E242615 “Component cannot be picked up.”
“不能吸取组件。”
E242616 “The state of DTS cannot be acquired.”
“不能取得 DTS 的状态。”
E242617 “The vision cannot be recognized. “
“不能进行图像识别。”
E242618 “Vision recognition condition data transmission error.”
“传送图像识别条件数据发生错误。”
E242619 “The head wait position is set in coordinates outside the moving range with a specified head.|Please
confirm the head wait position.”
“保护组件位置被设置在指定 Head 移动范围外的坐标。|请确认一下保护组件位置。”
E242620 “The pick position is set in coordinates outside the moving range with a specified head.”
“吸取位置被设置在指定 Head 移动范围外的坐标。”
E242621 “The SOT inspection stage is unused by the setup. “
“在设置中，SOT 检查器没有被选用。”
E242622 “The SOT inspection stage is dirty. Please remove the dirt of the SOT inspection stage.”
“SOT 检查器被弄脏。请清理 SOT 检查器。
E242623 “The lead does not exist within the detection window.”
“不能检测检查范围内的引脚。”
E242624 “Because directions of components of SOT are different by 180 degrees, the SOT direction cannot
be inspected.”
“因为 SOT 组件方向相差 180 度，不能检查 SOT 方向。”
E242625 “Because directions of components of SOT are different,the SOT direction cannot be inspected.”
“因为 SOT 组件方向不同，不能检查 SOT 方向。
E242626 “The error occurred by the SOT direction inspection by OCC.|Code:%ld”
“OCC 检查 SOT 方向发生错误。|代码:%ld”
E242627 “The VCS device is set in unused by the setup. “
“在机器设置中，没有选用 VCS。”
E242628 “The component size is out of range.”
“组件大小超出检查范围。”
E242629 “The LSC device is set in unused by the setup. “
“在机器设置中，没有选用 LSC 。”
E242630 “It failed in creating lighting data.”
“建立 LSC 照明数据出错。 “
E242631 “The optimum value of lighting data was unacquirable.”
“取得照明数据的优化值失败。 “
E242632 “Axis movement error (XH axis limit error)”
“轴移动出错（XH 轴驱动出错）。”
E242633 “The lsc cannot be recognized. “
“未能识别 LSC。”
E242634 “Error has occurred during LSC measurement.|Code: %ld”
“用 LSC 测量组件时，发生出错。|代码：%ld “
E242635 “Cannot move the head to pick position.”
“不是能移到吸取组件坐标的 Head。”
I242550 “Please detach components from the nozzle by the hand. “
“请手动取下吸嘴上的组件。”
Q242551 “Return of thin components to tape may fail due to weight. | continue return?”
“因为组件太小(1mm),归还可能失败。|是否执行归还？”
I242552 “Please set online for MTC.”
“请连接 MTC。”
I242553 “Remove a component in the case that there is a component | on a shuttle of MTC.”
“如果 MTC 滑梭上存在组件，请把它取下。”
Q242554 “There is a possibility this component has not been picked correctly. |Do you want to
continue?|(Tombstone height = %s)”
“可能组件站立。|是否继续？|(检测组件站立高度 = %s)”