JUKI贴片机错误代码.pdf - 第241页
E612042 “ A shadow i s detected while nozzl e detection afte r returning noz zles. (L2-head) ” “ 放回吸 嘴后，检查吸嘴是否存在时发现 阴影。 (L2 Head) “ E613042 “ A shadow i s detected while nozzl e detection afte r returning noz zles. (L3-h…
E613037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L3-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L3 Head) “
E614037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (L4-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(L4 Head) “
E615037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R1-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R1 Head) “
E616037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R2-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R2 Head) “
E617037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R3-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R3 Head) “
E618037 “The nozzle is too long. (over 0.6mm)|Please check the nozzle installation status. (R4-head)”
“ 吸嘴过长。(超过 0.6mm)|请检查吸嘴安装状态。(R4 Head) “
E611038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L1-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L1 Head) “
E612038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L2-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L2 Head) “
E613038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L3-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L3 Head) “
E614038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (L4-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(L4 Head) “
E615038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R1-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R1 Head) “
E616038”The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R2-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R2 Head) “
E617038”The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R3-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R3 Head) “
E618038 “The nozzle is too long. (over 0.3mm)|Please check the nozzle installation status. (R4-head)”
“ 吸嘴过长。(超过 0.3mm)|请检查吸嘴安装状态。(R4 Head) “
E611042 “A shadow is detected while nozzle detection after returning nozzles. (L1-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L1 Head) “
E612042 “A shadow is detected while nozzle detection after returning nozzles. (L2-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L2 Head) “
E613042 “A shadow is detected while nozzle detection after returning nozzles. (L3-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L3 Head) “
E614042 “A shadow is detected while nozzle detection after returning nozzles. (L4-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(L4 Head) “
E615042 “A shadow is detected while nozzle detection after returning nozzles. (R1-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R1 Head) “
E616042 “A shadow is detected while nozzle detection after returning nozzles. (R2-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R2 Head) “
E617042 “A shadow is detected while nozzle detection after returning nozzles. (R3-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R3 Head) “
E618042 “A shadow is detected while nozzle detection after returning nozzles. (R4-head)”
“ 放回吸嘴后，检查吸嘴是否存在时发现阴影。(R4 Head) “
E611047 “The cylinder to which the nozzle is returned is not appropriate. (L1-head)”
“ 放回吸嘴的圆筒位置不对。(L1 Head) “
E612047 “The cylinder to which the nozzle is returned is not appropriate. (L2-head)”
“ 放回吸嘴的圆筒位置不对。(L2 Head) “
E613047 “The cylinder to which the nozzle is returned is not appropriate. (L3-head)”
“ 放回吸嘴的圆筒位置不对。(L3 Head) “
E614047 “The cylinder to which the nozzle is returned is not appropriate. (L4-head)”
“ 放回吸嘴的圆筒位置不对。(L4 Head) “
E615047 “The cylinder to which the nozzle is returned is not appropriate. (R1-head)”
“ 放回吸嘴的圆筒位置不对。(R1 Head) “
E616047 “The cylinder to which the nozzle is returned is not appropriate. (R2-head)”
“ 放回吸嘴的圆筒位置不对。(R2 Head) “
E617047 “The cylinder to which the nozzle is returned is not appropriate. (R3-head)”
“ 放回吸嘴的圆筒位置不对。(R3 Head) “
E618047 “The cylinder to which the nozzle is returned is not appropriate. (R4-head)”
“ 放回吸嘴的圆筒位置不对。(R4 Head) “
E611049 “Laser sensor might be dirty. |Please clean the sensor. (L1-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(L1 Head) “
E612049 “Laser sensor might be dirty. |Please clean the sensor. (L2-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(L2 Head) “
E613049 “Laser sensor might be dirty. |Please clean the sensor. (L3-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(L3 Head) “
E614049 “Laser sensor might be dirty. |Please clean the sensor. (L4-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(L4 Head) “
E615049 “Laser sensor might be dirty. |Please clean the sensor. (R1-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(R1 Head) “
E616049 “Laser sensor might be dirty. |Please clean the sensor. (R2-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(R2 Head) “
E617049 “Laser sensor might be dirty. |Please clean the sensor. (R3-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(R3 Head) “
E618049 “Laser sensor might be dirty. |Please clean the sensor. (R4-head)”
“ 激光传感器可能被弄脏。|请把传感器擦干净。(R4 Head) “
E611050 “The error occurred by the return posture correction of the nozzle. (L1-head)”
“ 检查吸嘴姿势发生错误。(L1 Head) “
E612050 “The error occurred by the return posture correction of the nozzle. (L2-head)”
“ 检查吸嘴姿势发生错误。(L2 Head) “
E613050 “The error occurred by the return posture correction of the nozzle. (L3-head)”
“ 检查吸嘴姿势发生错误。(L3 Head) “
E614050 “The error occurred by the return posture correction of the nozzle. (L4-head)”
“ 检查吸嘴姿势发生错误。(L4 Head) “
E615050 “The error occurred by the return posture correction of the nozzle. (R1-head)”
“ 检查吸嘴姿势发生错误。(R1 Head) “
E616050 “The error occurred by the return posture correction of the nozzle. (R2-head)”
“ 检查吸嘴姿势发生错误。(R2 Head) “
E617050 “The error occurred by the return posture correction of the nozzle. (R3-head)”
“ 检查吸嘴姿势发生错误。(R3 Head) “