JUKI贴片机错误代码.pdf - 第45页
I242555 “ Please set onl ine for MTS .” “ 请连 接 MTS 。 ” I242556 “ Please close the door of MTS .” “ 请关 闭 MTS 的门。 ” I242557 “ Please insert the stacker of MTS .” “ 请装 入 MTS 的托盘存储箱。 ” I242558 “ Please attach the compone nt …
E242626 “The error occurred by the SOT direction inspection by OCC.|Code:%ld”
“OCC 检查 SOT 方向发生错误。|代码:%ld”
E242627 “The VCS device is set in unused by the setup. “
“在机器设置中，没有选用 VCS。”
E242628 “The component size is out of range.”
“组件大小超出检查范围。”
E242629 “The LSC device is set in unused by the setup. “
“在机器设置中，没有选用 LSC 。”
E242630 “It failed in creating lighting data.”
“建立 LSC 照明数据出错。 “
E242631 “The optimum value of lighting data was unacquirable.”
“取得照明数据的优化值失败。 “
E242632 “Axis movement error (XH axis limit error)”
“轴移动出错（XH 轴驱动出错）。”
E242633 “The lsc cannot be recognized. “
“未能识别 LSC。”
E242634 “Error has occurred during LSC measurement.|Code: %ld”
“用 LSC 测量组件时，发生出错。|代码：%ld “
E242635 “Cannot move the head to pick position.”
“不是能移到吸取组件坐标的 Head。”
I242550 “Please detach components from the nozzle by the hand. “
“请手动取下吸嘴上的组件。”
Q242551 “Return of thin components to tape may fail due to weight. | continue return?”
“因为组件太小(1mm),归还可能失败。|是否执行归还？”
I242552 “Please set online for MTC.”
“请连接 MTC。”
I242553 “Remove a component in the case that there is a component | on a shuttle of MTC.”
“如果 MTC 滑梭上存在组件，请把它取下。”
Q242554 “There is a possibility this component has not been picked correctly. |Do you want to
continue?|(Tombstone height = %s)”
“可能组件站立。|是否继续？|(检测组件站立高度 = %s)”
I242555 “Please set online for MTS.”
“请连接 MTS。”
I242556 “Please close the door of MTS.”
“请关闭 MTS 的门。”
I242557 “Please insert the stacker of MTS.”
“请装入 MTS 的托盘存储箱。”
I242558 “Please attach the component to the nozzle manually.”
“请手动给吸嘴安装组件。”
I242559 “The pickup of components succeeded. The measurement begins.”
“组件被成功吸着，开始测定。”
Q242560 “Failed in picking components. Do you want to make a retry?”
“组件吸着失败，是否重试？”
I242561 “Please install components by the hand in the chuck. When the button is pressed, the chuck is
close.”
“请把组件用手动安装在夹盘内。单击按钮，就关闭夹盘。”
Q242562 “Please press 'Yes' if the installation of components is a success. Please press 'No' when doing
again.”
“已成功安装组件，请单击[是]﹔重试，请单击[否]。”
Q242563 “Please press 'Yes' if detach components by the hand. Please press 'No' when scrap components.”
“手动取下组件，请单击[是]﹔废弃组件，请单击[否]。”
Q242564 “Are components returned ?”
“是否归还组件？”
Q242565 “The components pickuped on the head are returned.”
“归还 Head 上的组件。”
Q242567 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.20 times as much as specified at the maximum.”
“现在的参数存在不稳定的因素。是否继续取得参数？ |最多进行设置次数 x 20 回左右的
测量动作。”
Q242568 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.10 times as much as specified at the maximum.”
“当前照明条件下，发生识别错误，是否继续取得动作？|最多测量动作次数是设置次数
x10。”
E249001 “The origin point return is non-completion. Please operate again after completing the origin point
return”
“没有执行返回原点。|请执行返回原点后，再次操作。”
[Cause]
The axis has not yet been returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E249002 “The OCC device is unused. The bank mark recognition is aborted”
“没有使用 OCC 设备。| 停止识别台架标记。”
[Cause]
OCC or OCC2 was set not to “Use” in the Use unit in Setup when performing the Bank mark
recognition.
[Treatment]
Please set OCC or OCC2 to “Use” in the Use unit in Setup.
E249003 “The stop key was pressed. The bank mark recognition is aborted”
“停止按钮被按下。| 停止识别台架标记。”
[Cause]
The stop key was pressed while the Bank mark recognition was in operation.
[Treatment]
“OK” button will completely abort the Bank mark recognition process.
E249004”The axis cannot be moved to recognition position. The bank mark recognition is aborted”
“轴不能移到识别位置。| 停止识别台架标记。”
[Cause]
An error occurred in the axis traveling.
[Treatment]
E249005 “The bank mark recognition error. The bank mark recognition is aborted”
“识别台架标记出错。| 停止识别台架标记。”
[Cause]
An error occurred in the Mark recognition by OCC unit.
[Treatment]
Please check and see if feeder bank is dirty or if something is concealing the feeder bank.
If the mark does not fit in the frame, you need to adjust the mark.
E249006 “MTS power off”
“MTS 电源被关闭。”
[Cause]
The power supply of MTS is off.