JUKI贴片机错误代码.pdf - 第41页
“ 组件过 于倾斜。 ” E242532 “ Component size is too big .” “ 组件外 形尺寸过于偏大。 ” E242533 “ Component size is too small .” “ 组件外 形尺寸过于偏小。 ” E242534 “ Cannot recognize component .” “ 不能识 别组件。 ” E242535 “ Lead pitch of %s side is not c…
E242517 “The nozzle cannot be exchanged. “
“交换吸嘴失败。”
E242518 “The nozzle cannot be installed.”
“安装吸嘴失败。”
2
E242519 “There is no head which can be moved to the component pickup position.”
“Head 不能移到组件吸取坐标。”
E242520 “Component data error”
“组件数据错误。”
E242521 “The IC collection belt is unused by the setup. “
“在设置中，IC 回收器没有被选用。”
E242522 “The IC collection belt is fullness.”
“IC 回收器已被装满。”
E242523 “The chip standing was detected.”
“查出芯片站立。”
E242524 “The height of laser was not able to be measured from range.|Please confirm the height of
component.”
“不能检测在标准范围内的激光高度。|请确认一下组件高度。”
E242525 “The height of components was measured with 0mm or less.|Please confirm the height of laser.”
“测量组件高度结果为负值。|请确认一下组件高度。”
E242526 “Laser measurement error (MCM driver error) “
“激光测量发生错误(MCM 驱动错误) “
E242527 “Because the lower bound of being able the axis movement had been exceeded,|the height of the
laser was not able to be measured.”
“因为超过轴移动范围的下限，不能测量激光高度。”
E242528 “Could not change of mode for the chip verification system.”
“变更数值检查装置的测量模式失败。”
E242529 “Chip verification detection error.”
“数值检查装置测量发生错误。”
E242530 “The chip verification system is unused by the setup. “
“在设置中，数值检查装置没有被选用。”
E242531 “Component angle exceeds limit value.”
“组件过于倾斜。”
E242532 “Component size is too big.”
“组件外形尺寸过于偏大。”
E242533 “Component size is too small.”
“组件外形尺寸过于偏小。”
E242534 “Cannot recognize component.”
“不能识别组件。”
E242535 “Lead pitch of %s side is not conform.”
“%s 的引脚间距不一致。”
E242536 “Cannot recognize lead of %s side.”
“不能识别%s 的引脚间距。”
E242537 “Error has occurred during VCS measurement.|Code: %ld”
“VCS 测量组件发生错误。|代码: %ld”
E242538 “MTC is not power on.”
“没有打开 MTC 电源。”
E242539 “MTC is not online.”
“没有连接 MTC。”
E242540 “MTC is in the supply state.”
“MTC 处于补充状态。”
E242541 “MTC is disable.”
“不能使用 MTC。”
E242542 “MTC Emergency Switch is Pressed.”
“MTC 处于紧急停止状态。”
E242543 “MTC initialize not done.”
“未初始化 MTC。”
E242544 “MTC failed to a supply of a component.”
“MTC 供给组件失败。”
E242545 “The component remainder number is 0.”
“组件剩余数为 0。”
E242546 “TF driver error. |Code: %ld”
“TF 驱动错误 |代码: %ld”
E242547 “MTS is not power on.”
“没有打开 MTS 电源。”
E242548 “MTS is not online.”
“没有连接 MTS。”
E242549 “MTS is disable.”
“不能使用 MTS。”
E242600 “MTS failed to pull a tray.”
“MTS 取出托盘失败。”
E242601 “MTS failed to store a tray.”
“MTS 储存托盘失败。”
E242602 “MTS cannot move because of cover opening.”
“打开主机盖时，MTS 停止动作。”
E242603 “The door of MTS opens.”
“MTS 的门被打开。”
E242604 “The stacker of MTS is empty.”
“MTS 没有安装托盘存储箱。”
E242605 “MTS Emergency Switch is Pressed.”
“MTS 处于紧急停止状态。”
E242606 “MTS initialize not done.”
“未初始化 MTS。”
E242607 “DTS is disable.”
“不能使用 DTS。”
E242608 “DTS cannot be executed.”
“DTS 不能运行。”
E242609 “DTS is not initialized.”
“未初始化 DTS。”
E242610 “DTS safety cover opens.”
“DTS 安全盖被打开。”
E242611 “DTS is in the state of supply.”