JUKI贴片机错误代码.pdf - 第216页
“ Z 轴移动前，查出了超过移动范围的指定坐标。 ” E610067 “ An error occur red when opening the ATC support plate .” “ 打开 ATC 滑板出错。 ” E610068 “ An error occur red when shutting the ATC support plate .” “ 关闭 ATC 滑板出错。 ” E610069 “ A t ime-out oc…
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610053 “An error occurred when detecting the presence of Laser nozzle.”
“检查吸嘴是否存在时发生错误。”
E610054 “Nozzle information (externals size of the nozzle) is not defined.”
“吸嘴信息(吸嘴外形大小)没有被定义。”
E610055 “Because the nozzle is too large, it is not possible to install in the MNLA head.”
“因吸嘴过大，不能安装在 MNLA Head 上。”
E610056 “A large-scale nozzle cannot be installed in the MNLA head.”
“MNLA Head 上，不能安装大型吸嘴。”
E610057 “The error occurred by the installation posture correction of the nozzle.”
“校正吸嘴姿势出错。”
E610058 “The installation posture of the nozzle is abnormal.”
“吸嘴安装姿势错误。”
E610059 “The nozzle is reversely installed in ATC.”
“吸嘴倒立安装在 ATC。”
E610060 “There is a possibility that parts arrive. |The nozzle cannot be returned.”
“吸嘴上可能附有组件。|不能放回吸嘴。”
E610061 “The nozzle is too short. |Please check the nozzle.”
“吸嘴过短。|请检查吸嘴。”
E610062 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610063 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610064 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610065 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610066 “Z Axis detect Cordinates outof Limit Range.”
“Z 轴移动前，查出了超过移动范围的指定坐标。”
E610067 “An error occurred when opening the ATC support plate.”
“打开 ATC 滑板出错。”
E610068 “An error occurred when shutting the ATC support plate.”
“关闭 ATC 滑板出错。”
E610069 “A time-out occurred when opening the ATC(L) support plate.”
“打开 ATC(左)滑板超时。”
E610070 “A time-out occurred when opening the ATC(R) support plate.”
“关闭 ATC(左)滑板超时。”
E610071 “A time-out occurred when shutting the ATC(L) support plate.”
“打开 ATC(右)滑板超时。”
E610072 “A time-out occurred when shutting the ATC(R) support plate.”
“关闭 ATC(右)滑板超时。”
E610073 “ATC(L) support plate sensor is abnormal.”
“ATC(左)滑板传感器异常。”
E610074 “ATC(R) support plate sensor is abnormal.”
“ATC(右)滑板传感器异常。”
E610075 “ATC(L) support plate can not be shut down.”
“不能关闭 ATC(左)滑板。”
E610076 “ATC(R) support plate can not be shut down.”
“不能关闭 ATC(右)滑板。”
E610077 “The nozzle cannot be detected by measuring the length of the nozzle.|Please confirm the nozzle.”
“测量吸嘴长度时，没有发现吸嘴。|请检查吸嘴。”
E610078 “The length of the nozzle is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610079 “The length of the nozzle is too short.|Please confirm the nozzle.”
“吸嘴长度过短。|请检查吸嘴。”
E610080 “The nozzle is long and length is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610081 “The length of the measured nozzle exceeds tolerance.|Please confirm the nozzle.”
“吸嘴长度的测量结果超过允许范围。|请检查吸嘴。”
E610082 “The length of the measured nozzle does not fill tolerance.|Please confirm the nozzle.”
“吸嘴长度的测量结果没有达到允许范围。|请检查吸嘴。”
E610083 “The gotten nozzle width does not meet that of allocated nozzle.|The machine will not return the
nozzle.|Check condition of the nozzle.|Select <No> to return the nozzle.”
“测定的吸嘴宽度与设置的吸嘴宽度不一致。|不能返回吸嘴。|选择〈否〉返回吸嘴。”
E610084 “A vacuum goes up too much. The nozzle may be choked up.|Please confirm the nozzle.”
“真空过大。可能吸嘴被塞满。|请检查吸嘴。 “
E610085 “Axes Driver:| XY-axis can not move.| Feeder float detected.”
“XY 轴不能移动。|发现传送带浮动。”
E610086 “Axes Driver:| X-axis can not move.| Feeder float detected.”
“X 轴不能移动。|发现传送带浮动。”
E610087 “Axes Driver:| Y-axis can not move.| Feeder float detected.”
“Y 轴不能移动。|发现传送带浮动。”
E610088 “Axes Driver:| XR-axis can not move.| Feeder float detected.”
“XR 轴不能移动。|发现传送带浮动。”
E610089 “Axes Driver:| YC-axis can not move.| Feeder float detected.”
“YC 轴不能移动。|发现传送带浮动。”
E610090 “Axes Driver:| YR-axis can not move.| Feeder float detected.”
“YR 轴不能移动。|发现传送带浮动。”
E610091 “The vacuum of a head did not go up.”
“ head 的真空没有上升。”
E610092 “Head is equipped with the nozzle of an exchange error.|Please check the wearing state of a nozzle.”
“ 吸嘴发生交换错误。|请检查吸嘴的安装状态。”
E610093 “The head is equipped with the inaccurate nozzle.|Please confirm the nozzle.”
“ head 上安装的吸嘴错误。|请检查吸嘴。”
E610100 “The Vacuum calibration has not been installed”
“没有设置真空校准。”
[Cause]
The installation position of the vacuum calibration has not been set.
[Treatment]