JUKI贴片机错误代码.pdf - 第106页
[Cause] This error occurs if MTC Home ret urni ng has not been complete y et when starting a producti on. [Treatment] OK button : Performs MTC Home returning. Cancel button : Will have you back t o the status that is bef…
[Cause]
A production program that was created by HLC was read in and its production is about to get started
with the connection between your machine and HLC being OFF.
[Treatment]
Please enable the connection between your machine and HLC in the Setup or read in another
production program.
E500902 “Online switch is not effective to the Setup data though the connection with HLC is turning on”
“设置数据上已经选择了连接 HLC，但联机按钮为无效。”
[Cause]
Online switch is not available while the connection between your machine and HLC is ON in the
Setup data.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or enable the online
switch.
E501000 “MTC Move Failed”
“因 MTC 运转出错，停止生产。”
[Cause]
This error occurs when an error occurs from MTC during a production.
[Treatment]
Please turn off the power supply of MTC and examine it.
E501010 “MTC Power is Off. Please Power On”
“MTC 电源被关闭，|请打开电源。”
[Cause]
This error occurs if MTC is not ON when starting a production.
[Treatment]
Please turn on the power supply of MTC and press OK button. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501011 “MTC Emergency Switch is Pressed. Please Release the Switch”
“MTC 被处于紧急停止状态，|请解除紧急按钮。”
[Cause]
This error occurs if the Emergency Switch of MTC has been pressed when starting a production.
[Cause]
Please press OK button after disabling the Emergency Switch. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501012 “MTC is No Original”
“MTC 未完成返回原点。”
[Cause]
This error occurs if MTC Home returning has not been complete yet when starting a production.
[Treatment]
OK button : Performs MTC Home returning.
Cancel button : Will have you back to the status that is before pressing START key.
E501013 “MTC is off-line Condition. Please change to on-line”
“MTC 处于脱机状态，|请连接 MTC。”
[Cause]
This error occurs if MTC is Offline when starting a production.
[Treatment]
Please put MTC in online status and press OK button. Pressing Cancel button will have you back to
the status that is before pressing START key.
E501014 “MTC is Door Open Condition. Please Close Cover”
“MTC 的门被打开，|请关上门。”
[Cause]
This error occurs if MTC door is open when starting a production.
[Treatment]
Please close the MTC door then press OK button. Pressing Cancel button will have you back to the
status that is before pressing START key.
E501015 “MTC is Cover Open Condition. Please Close Cover”
“MTC 机盖被打开，|请关闭机盖。”
[Cause]
This error occurs if MTC cover is open when starting a production.
[Treatment]
Please close the MTC cover then press OK button. Pressing Cancel button will have you back to the
status that is before pressing START key.
E501016 “MTC is Error Condition”
“MTC 发生错误。”
[Cause]
This error occurs if MTC is in an error status when starting a production.
[Treatment]
Please turn off the power supply of MTC and examine it.
E501017 “MTC is Change Component Condition. Please Release the Change Condition”
“MTC 处于交换组件状态，|请解除交换状态。”
[Cause]
This error occurs if MTC is in a status where MTC needs a component change when starting a
production.
[Treatment]
Please disable the status of MTC, and press OK button.
E501018 “Component exists on the MTC Shuttle. Please Remove Component from Shuttle”
“MTC 滑梭上存在组件，|请取下组件。”
[Cause]
This error occurs if any components are on the shuttle of MTC when starting a production.
[Treatment]
Please remove those components from the MTC shuttle and press OK button.
E501019 “Because MTC is Change Component Condition, home position return cannot be done. Please
Release the Change condition”
“因 MTC 处于组件交换状态，不能进行返回原点。|请解除组件交换状态。”
[Cause]
This error occurs if MTC is in a status where MTC needs a component change when performing the
Home returning of MTC.
[Treatment]
Please disable the status of MTC, and press OK button.
E501020 “There is no MTC Component in the production program.”
“生产程序内不存在 MTC 组件。”
E501021 “MTC failed to return to the ORIGIN.|Would you like to have MTC return to Home Position?”
“MTC 返回原点失败，|是否重新执行返回原点？”
E501100 “MTS power off”
“MTS 电源被关闭，|请打开电源。”
[Cause]
MTS was not ON when starting a production.
[Treatment]
Please turn on the power supply of MTS and press OK button. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501101 “MTS offline”
“MTS 处于脱机状态。”
[Cause]
MTS was not online when starting a production.
[Treatment]
Please put MTC in online status and press OK button. Pressing Cancel button will have you back to
the status that is before pressing START key.