JUKI贴片机错误代码.pdf - 第215页
‧If the error occurred after th e installati on or the version up of the software, you need t o re-install the software. ‧If the treatments above do not work, there is a possibility t h at MPX board(s) in the machine is …
the data image does not appear at this point, please turn off the power supply of your machine and try
again. If the data image still does not get displayed after the retry, there is a possibility that the MCM
board in the laser sensor is not installed properly or that the sensor itself is broken. Please turn off the
power supply and examine the installation status of the MCM board in the sensor.
E610051 “The nozzle can not be returned since its posture is abnormal”
“因为吸嘴姿势不对，不能放回吸嘴。”
[Cause]
Nozzle returning got discontinued since a posture of the nozzle exceeded the permissive value during
the Nozzle posture checking by laser prior to a nozzle change.
[Treatment]
Please take the nozzle off manually. Please examine the installation status of a nozzle installed on the
head to find a cause of the error. Treatments to take vary, depending on whether nozzles are set in
the ATC properly or not.
1. If a nozzle rotated against its installation angle to ATC.
There is a possibility that the nozzle rotated during the production. The nozzle might be rotated
manually when the production stopped temporary.
Nozzle rotate every once in a while when a production is done for a long time (over a week) without
changing any nozzles.
If the nozzle rotation occurs during a few-hour production, there is a possibility that the nozzle is
abnormal. You need to replace the nozzle with a new one. If the error occurs regardless the nozzle
types, you need to replace a clamp part with a new one since it may be worn away.
2. If a nozzle did not rotate against its installation angle to ATC.
‧The nozzle shape is abnormal. Please examine if the green plastic part is chipped or not. Also,
please see if there is anything attached to the nozzle.
‧If the installation angle is slanting to a certain side, there is a possibility that the laser measurement
unit is not judging the angle correctly. In this case, the connecting cable between the laser
measurement unit and the servo driver may have a problem. Please take off the cable and re-install it.
‧If the error still occurs, there is a possibility that the MCM board in the laser sensor is not installed
properly or that the MCM board itself is broken. Please turn off the power supply of your machine
and check the installation status of the MCM board in the Laser recognition unit.
E610052 “ATC X coordinate is abnormal”
“X 坐标参数不正确。”
[Cause]
The head could not move to the specified ATC position. Some program versions in the machine may
be clashing with each other.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610053 “An error occurred when detecting the presence of Laser nozzle.”
“检查吸嘴是否存在时发生错误。”
E610054 “Nozzle information (externals size of the nozzle) is not defined.”
“吸嘴信息(吸嘴外形大小)没有被定义。”
E610055 “Because the nozzle is too large, it is not possible to install in the MNLA head.”
“因吸嘴过大，不能安装在 MNLA Head 上。”
E610056 “A large-scale nozzle cannot be installed in the MNLA head.”
“MNLA Head 上，不能安装大型吸嘴。”
E610057 “The error occurred by the installation posture correction of the nozzle.”
“校正吸嘴姿势出错。”
E610058 “The installation posture of the nozzle is abnormal.”
“吸嘴安装姿势错误。”
E610059 “The nozzle is reversely installed in ATC.”
“吸嘴倒立安装在 ATC。”
E610060 “There is a possibility that parts arrive. |The nozzle cannot be returned.”
“吸嘴上可能附有组件。|不能放回吸嘴。”
E610061 “The nozzle is too short. |Please check the nozzle.”
“吸嘴过短。|请检查吸嘴。”
E610062 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610063 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610064 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610065 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610066 “Z Axis detect Cordinates outof Limit Range.”
“Z 轴移动前，查出了超过移动范围的指定坐标。”
E610067 “An error occurred when opening the ATC support plate.”
“打开 ATC 滑板出错。”
E610068 “An error occurred when shutting the ATC support plate.”
“关闭 ATC 滑板出错。”
E610069 “A time-out occurred when opening the ATC(L) support plate.”
“打开 ATC(左)滑板超时。”
E610070 “A time-out occurred when opening the ATC(R) support plate.”
“关闭 ATC(左)滑板超时。”
E610071 “A time-out occurred when shutting the ATC(L) support plate.”
“打开 ATC(右)滑板超时。”
E610072 “A time-out occurred when shutting the ATC(R) support plate.”
“关闭 ATC(右)滑板超时。”
E610073 “ATC(L) support plate sensor is abnormal.”
“ATC(左)滑板传感器异常。”
E610074 “ATC(R) support plate sensor is abnormal.”
“ATC(右)滑板传感器异常。”
E610075 “ATC(L) support plate can not be shut down.”
“不能关闭 ATC(左)滑板。”
E610076 “ATC(R) support plate can not be shut down.”
“不能关闭 ATC(右)滑板。”
E610077 “The nozzle cannot be detected by measuring the length of the nozzle.|Please confirm the nozzle.”
“测量吸嘴长度时，没有发现吸嘴。|请检查吸嘴。”
E610078 “The length of the nozzle is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610079 “The length of the nozzle is too short.|Please confirm the nozzle.”
“吸嘴长度过短。|请检查吸嘴。”
E610080 “The nozzle is long and length is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610081 “The length of the measured nozzle exceeds tolerance.|Please confirm the nozzle.”