JUKI贴片机错误代码.pdf - 第217页
“ 吸嘴长 度的测量结果超过允许范围。 | 请检查吸 嘴。 ” E610082 “ The lengt h of the measured nozzl e does not fill t olerance.|Plea se confirm the nozzle .” “ 吸嘴长 度的测量结果没有达到允许范围 。 | 请检查吸嘴。 ” E610083 “ The got ten nozzle width does not meet tha…
“Z 轴移动前，查出了超过移动范围的指定坐标。”
E610067 “An error occurred when opening the ATC support plate.”
“打开 ATC 滑板出错。”
E610068 “An error occurred when shutting the ATC support plate.”
“关闭 ATC 滑板出错。”
E610069 “A time-out occurred when opening the ATC(L) support plate.”
“打开 ATC(左)滑板超时。”
E610070 “A time-out occurred when opening the ATC(R) support plate.”
“关闭 ATC(左)滑板超时。”
E610071 “A time-out occurred when shutting the ATC(L) support plate.”
“打开 ATC(右)滑板超时。”
E610072 “A time-out occurred when shutting the ATC(R) support plate.”
“关闭 ATC(右)滑板超时。”
E610073 “ATC(L) support plate sensor is abnormal.”
“ATC(左)滑板传感器异常。”
E610074 “ATC(R) support plate sensor is abnormal.”
“ATC(右)滑板传感器异常。”
E610075 “ATC(L) support plate can not be shut down.”
“不能关闭 ATC(左)滑板。”
E610076 “ATC(R) support plate can not be shut down.”
“不能关闭 ATC(右)滑板。”
E610077 “The nozzle cannot be detected by measuring the length of the nozzle.|Please confirm the nozzle.”
“测量吸嘴长度时，没有发现吸嘴。|请检查吸嘴。”
E610078 “The length of the nozzle is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610079 “The length of the nozzle is too short.|Please confirm the nozzle.”
“吸嘴长度过短。|请检查吸嘴。”
E610080 “The nozzle is long and length is too long.|Please confirm the nozzle.”
“吸嘴长度过长。|请检查吸嘴。”
E610081 “The length of the measured nozzle exceeds tolerance.|Please confirm the nozzle.”
“吸嘴长度的测量结果超过允许范围。|请检查吸嘴。”
E610082 “The length of the measured nozzle does not fill tolerance.|Please confirm the nozzle.”
“吸嘴长度的测量结果没有达到允许范围。|请检查吸嘴。”
E610083 “The gotten nozzle width does not meet that of allocated nozzle.|The machine will not return the
nozzle.|Check condition of the nozzle.|Select <No> to return the nozzle.”
“测定的吸嘴宽度与设置的吸嘴宽度不一致。|不能返回吸嘴。|选择〈否〉返回吸嘴。”
E610084 “A vacuum goes up too much. The nozzle may be choked up.|Please confirm the nozzle.”
“真空过大。可能吸嘴被塞满。|请检查吸嘴。 “
E610085 “Axes Driver:| XY-axis can not move.| Feeder float detected.”
“XY 轴不能移动。|发现传送带浮动。”
E610086 “Axes Driver:| X-axis can not move.| Feeder float detected.”
“X 轴不能移动。|发现传送带浮动。”
E610087 “Axes Driver:| Y-axis can not move.| Feeder float detected.”
“Y 轴不能移动。|发现传送带浮动。”
E610088 “Axes Driver:| XR-axis can not move.| Feeder float detected.”
“XR 轴不能移动。|发现传送带浮动。”
E610089 “Axes Driver:| YC-axis can not move.| Feeder float detected.”
“YC 轴不能移动。|发现传送带浮动。”
E610090 “Axes Driver:| YR-axis can not move.| Feeder float detected.”
“YR 轴不能移动。|发现传送带浮动。”
E610091 “The vacuum of a head did not go up.”
“ head 的真空没有上升。”
E610092 “Head is equipped with the nozzle of an exchange error.|Please check the wearing state of a nozzle.”
“ 吸嘴发生交换错误。|请检查吸嘴的安装状态。”
E610093 “The head is equipped with the inaccurate nozzle.|Please confirm the nozzle.”
“ head 上安装的吸嘴错误。|请检查吸嘴。”
E610100 “The Vacuum calibration has not been installed”
“没有设置真空校准。”
[Cause]
The installation position of the vacuum calibration has not been set.
[Treatment]
If the vacuum calibration unit has not been installed on ATC, please install it.
You can set the installation position of the vacuum calibration as follows.
Please select [Machine Setup] from the menu bar, and then [Setting Group(G)] [ATC Nozzle
Allocation(A)]. If you right-click the mouse on the nozzle type of the ATC number on which the
vacuum calibration unit is installed, a list box is shown. Select 'Vac Unit' in there.
E610200 “Emergency Stop SW occurred”
“发生紧急停止。”
[Cause]
The Emergency Stop SW was pressed.
[Treatment]
Please unlock the Emergency Stop SW and hit the OK key.
E610201 “Area sensor F ON occurred”
“发生范围传感器(前侧)启动。”
[Cause]
The area sensor on the front side got ON.
[Treatment]
Please hit the OK key and then perform the Home returning.
E610202 “Area sensor R ON occurred”
“发生范围传感器(后侧)启动。”
[Cause]
The area sensor on the rear side got ON.
[Treatment]
Please hit the OK key and then perform the Home returning.
E610203 “Cover open sensor ON occurred”
“机盖被打开。”
[Cause]
The Safety cover is open.
[Treatment]
Please close the Safety cover.
E610204 “Feeder floatation sensor ON occurred”
“发生传送带浮动传感器被启动。”
[Cause]
The Feeder floatation sensor detected something.
[Treatment]
The error occurs when the Feeder floatation sensor is interrupted. If there is anything that interrupts
the sensor, please remove it.